gentoo siocsifflags error Wilson Wyoming

Address 565 W Broadway Ave, Jackson, WY 83001
Phone (307) 734-9415
Website Link http://www.jhcomputerclinic.com
Hours

gentoo siocsifflags error Wilson, Wyoming

This should solve the problem, you should longer have the ioctl(SIOCSIFFLAGS) failed: Name not unique on network message. What is the first movie to show this hard work message at the very end? I'm using the rt73-cvs-2008042605 driver (from the daily build). Linux changed my life~!

Conference presenting: stick to paper material? bada339ba24dee9e143bfb42e1dc61f146619846 is first bad commit commit bada339ba24dee9e143bfb42e1dc61f146619846 Author: Jeff Garzik Date: Tue Oct 23 20:19:37 2007 -0700 [NET]: Validate device addr prior to interface-up Signed-off-by: Jeff Garzik Signed-off-by: David ath45..) The original problem description and solution can be found in this forum thread. Enter “iwconfig”: lo no wireless extensions.

It likely looks similar the following output. So, I tried to execute the ifconfig command listen above but \ I
> got that error. Which one? No progress However, as above I created a debug-dump but this time with debug=31.

The source of the problem comes from the udev persistent net rules generator. Join our community today! Determining the Current Channel To determine the current channel, enter “iwlist channel”. Are there some directions somewhere you can point me to?

and, OH, BTW once running a rmmod - modprobe -v rt73 sequence the module crashed, leaving some relicts in kernel space, freezing my system. The second problem is that if you run airmon-ng on wifi0 the athXX created does not show as being shown as in Monitor mode, even though it is. Comment 16 Francois Romieu 2008-02-01 00:08:34 UTC ace@staticwave.ca 2008-01-31 20:57 : > Not sure if this is relevent, but the ifconfig reports something odd for the > "Base address": Base address For all drivers except madwifi-ng: airmon-ng stop For madwifi-ng, first stop ALL interfaces: airmon-ng stop athX Where X is 0, 1, 2 etc.

Plugging in and out doesn't help. mon0: ERROR while getting interface flags: No such device This means you have an old version of airmon-ng installed. Also, Unknown error 132 is a typical error for that. eth0 no wireless extensions.

Jan 27 10:52:52 mythbox 0000:00:04.0: SiS 190 PCI Fast Ethernet adapter at f8938000 (IRQ: 20), 00:00:00:00:00:00 Jan 27 10:52:52 mythbox eth0: RGMII mode. power requirements is good information. when i do a rfkill list it shows my wlan0 card a - softblocked yes - hardblocked yes so i turn the HW switch to on, and do a # rfkill If you no longer need the monitor interface and want to remove it, use the following: airmon-ng stop monX X is the monitor interface number - 0 unless you run multiple

Thanks, dyle71 29-04-2008 03:14:00 Hi Vern, Thank you for trying. It is strongly recommended that these processes be eliminated prior to using the aircrack-ng suite. “check kill” will check and kill off processes that might interfere with the aircrack-ng suite. ath0 IEEE 802.11b ESSID:"" Nickname:"" Mode:Managed Channel:0 Access Point: Not-Associated Bit Rate:0 kb/s Tx-Power:0 dBm Sensitivity=0/3 Retry:off RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality:0 Signal level:0 Noise level:0 Refer to the documentation above to kill network managers and put it back into monitor mode.

It depends on which driver you are using. It most likely mean the interface mode was changed from monitor to managed mode by a network manager. ifconfig shows active interfaces only. No flashing, no blinking, no nothing ...

and, oh yes, it's a Gentoo system. so far, downgrading the kernel is the only solution im finding, and the amount of time it took me to get a working gentoo was insane. If you wish to use the nextgen driver, make sure there are no scripts that load the legacy driver. The time now is 10:32 PM.

so, I used "iwlist wlan0 scanning", it gave me this error:"err:Network is down"If I use "ifconfig wlan0 up", it will give me this:"SIOCSIFFLAGS:No such file or directory"If I use "dhcpcd wlan0", Apr 29 06:22:42 moghedien rt73: probe of 4-1:1.0 failed with error -16 Apr 29 06:22:42 moghedien usbcore: registered new interface driver rt73 Apr 29 06:22:47 moghedien BUG: unable to handle kernel Thank you, Leandro [Attachment #3 (text/html)] Hi list,

# ifconfig eth0:0 192.168.1.3
SIOCSIFADDR: File \ exists
SIOCSIFFLAGS: Cannot assign requested address

My /etc/conf.d/net is \ correct:

config_eth0=( " 192.168.1.2 \ netmask

huh? Offline #6 2008-10-07 23:40:24 wxiluo Member Registered: 2008-09-26 Posts: 18 Website Re: [solved]Wireless, wlan0 can't be wake up... Offline #9 2008-10-08 12:10:44 wxiluo Member Registered: 2008-09-26 Posts: 18 Website Re: [solved]Wireless, wlan0 can't be wake up... any help much appreciated.

share|improve this answer edited May 10 '15 at 13:19 Mateo 6,58884264 answered May 10 '15 at 11:42 user4780495 8115 works perfect for me (15.04), thanks :) –Muhammad Sufiyan Oct If this does not resolve the problem then follow the advice in this thread. I don't know why. Then: wlanconfig ath create wlandev wifi0 wlanmode sta See madwifi-ng site documentation.

To start ath0 in monitor mode: airmon-ng start wifi0 System responds: Interface Chipset Driver wifi0 Atheros madwifi-ng ath0 Atheros madwifi-ng VAP (parent: wifi0) (monitor mode enabled) Now enter “iwconfig” System responds: On Ubuntu, do “apt-get install madwifi-tools”. Why (in universe) are blade runners called blade runners? Thanks, dyle71 28-04-2008 03:55:27 Hello Vern, Thank you for reply!

See it's an old Dell C600 which just supports USB 1.1. If that doesn't work, build with debug enabled, then modbprobe with "debug=15" as a parameter, followed immediately with an rmmod.