frigidaire gallery series stove f10 error Sinclair Wyoming

Address 1541 Diamond Dr, Casper, WY 82601
Phone (307) 215-8800
Website Link https://www.cmitsolutions.com/wyoming-center
Hours

frigidaire gallery series stove f10 error Sinclair, Wyoming

Your model has been added. Bad EEPROM Identification/Checksum error. 1. (F10 only) Check *RTD Sensor Probe & replace if necessary. If resistance does not match the chart, replace the RTD sensor probe. Thank you for your question.

Wire nuts (pack of 10) AP5641944 Good luck and keep us posted. Gene. Thank you for your question. The plug is behind the range normally at the bottomJACUSTOMER-nuon2qee- :Thank you, my spouse will be home shortly, if we have any follow up questions will you be online in the

There are a few things that can cause it. The wires look OK (no visible external wear) from the plastic connector in the back of the EOC module down to the metal bracket holding the RTD temperature sensor into the Keep me posted. We ordered both the parts, tried the EOC first, with no fix.

The part number for the oven relay board 316443920 You can order the part by clicking on the part number. If you checked the temperature probe at the EOC plug then the EOC itself has failed and would need to be replaced. The temperature may be increased as much as 35°F (19°C). 4. roy // Mar 28, 2015 at 7:30 am i have a frigidaire stove model# pfef373es2 and it was flashing f11 so i replaced the eoc and worked for 1 day and

Michele Gene // May 10, 2015 at 9:56 pm Hello Michele, Sorry for the delay. Any assistance is much appreciated. Keep me posted please. If the reading is incorrect, the temperature probe (sensor) would need to be replaced.

Unplug the range and remove the rear panel. Now it wont let me set the clock to the right time. I replaced the EOC and it has been fine for about 3 months and now is doing it again. In order to provide most accurate advice I need the complete model number of the oven and the part number of the EOC you installed.

Your welcome. com then you can easy return them. model plgf389cce Frigidaire professional series Gene // May 17, 2015 at 6:34 pm Hello Greg. Locate the temperature sensor (RTD) plug on the control board (EOC).

Gene // Dec 18, 2014 at 7:58 pm Hello Jim, Sorry for the delay. I'm thinking that replacing the wiring harness might be warranted, but it looks like a chore to access the rest of it, and I don't see a part number for it SteveB // May 13, 2015 at 2:57 pm Hello we have a Frigidaire electric range model PLES389ECB it is showing an f30 code I have replaced both the probe and EOC. So should my next step be to get a new EOC?

If I should replace the range, is this a common and eventual issue with all electric ranges and the electronics on them? Ed // Apr 27, 2015 at 11:01 am Hi Gene, Per your suggestion, I cut the 2 violet wires (the 2 running between the EOC and the RTD temperature sensor) and Gene. The part number for the EOC is 316418735 To order a part just click on the part number.

If not please don't forget to hit the accept button. Could the oven control data be used to verify these failures, maybe downloaded by a tech ? In regards to my Electrolux Icon electric wall oven E30EW75GPS1 In addition to the broiler coming on all by itself and this overheating the oven, we also noticed sometimes during baking Well, it was almost a year to the date.

Sorry, was offline.When the oven is put onto bake and the temperature is set, (ex. 350 deg F) once it reaches that temperature, the pre-heat light goes off, but the heating Frank // Nov 4, 2014 at 3:56 pm I have an Electrolux model#EW30DF65GSB. The F11 error code means that control has sensed a shorted keypad. i am adding the link below to help you with your question while you wait for your expert response.

Code f10. darlene // Dec 19, 2014 at 7:03 pm The frigidaire stove my son has has a f10 code. We’re going to check resistance though the sensor and the wire harness next. Thank you for your question.