fax machine error messages Lander Wyoming

First Call Communications is your full-service provider of business telephone systems, voice and data cabling, IP network cameras, and network support. We have over 40 years of combined experience in these industries. We service small and large customers throughout Wyoming and Western Nebraska. With our dedicated staff, we can provide a virtual end-to-end solution for all of your IT and communication needs. Call us today for more information.

Address 642 N Glenn Rd, Casper, WY 82601
Phone (307) 439-5999
Website Link http://www.firstcallwyoming.com
Hours

fax machine error messages Lander, Wyoming

Solution: Replace the G3 modem control unit (MOD2 unit, etc.). ##237 [ RX ] DECODE control UPI malfunction. Configure the remote machine for poll transmission. Cause: Too much power applied to the Thermal head. A.

Place the original in the correct orientation. Failed Alerting No Answer. Cause: Carriage motor does not work. Solution: Adjust the NL equalizer so that the other party can properly receive TCF.

Cause: Other party cannot receive signal properly due to poor line conditions. Retry the fax reception when telephone line conditions have improved. Solution: Replace the SCNT PWB. ##334 [ TX / RX ] Printer control EEPROM check error. Cause: The other party experienced echo malfunction.

Cause: Presence of tariff pulse. ##109 [ TX ] Receive signals other than DIS, DTC, FTT, CFR or CRP after DCS transmission and exceeded the number of protocol retransmission during Cause: Malfunction due to CFR echo. Solution: Lower the transmission level to prevent echo reception of transmitted CFR. ##115 [ TX ] Exceeded the one-line maximum transmission time (5 seconds) during picture transmission. Cause: Abnormal protocol.

Cause: The other party released the line during transmission. Cause: Other party cannot receive DIS signal properly due to poor line conditions. Solution: Boost the transmission level so that the other party can receive picture or Q signals properly. Disable ECM.

Solution: Transmit to a FAX whose bits 33 and over are not covered by recommendations. Received bad response to DCS or training An unexpected message was received when the bulk fax service asked for the remote fax machine's fax capabilities. Cause: Defective DRAM memory. Solution: Lower the transmission level to prevent the reception of echo signals. ##107 [ RX ] Fall back failure on TX side during reception.

Solution: Replace NCU PWB ##263 [ TX / RX ] Fail to respond for 20 seconds after detecting preamble. Cause: Defective internal unit; (+24 volts down). Solution: Replace the SCNT PWB. ##267 [ TX / RX ] Internal memory error. Cause: The other party cannot receive picture signals or EOM properly due to poor line conditions.

A. Cause: The ink sensor is defective. Solution: Boost the transmission level so that the other party can receive DIS properly. Solution: Replace voice memory attached unit. ##603 [ TX ] Fail MCF reception during MF1 transmission.

If you cannot make calls this way, contact your telephone company. Z7_3054ICK0KGTE30AQO5O3KA30N0 hp-concentra-wrapper-portlet Actions ${title} Loading... Cause: The other party cannot receive the signals immediately before GC2, PIS or the Phase signals properly due to poor line conditions. Solution: Replace the board containing a printer control ROM B.

Related Articles Home Solutions Forums Return to Website An unexpected error occured. Solution: Record the protocol on DAT tape and then request the Canon Technical center to analyze the information. ##738 [ RX ] Wrong block number during ARQ reception. Confirm that the local user really wants to attempt a poll reception. Solution: Replace the G2 modem control unit (MOD2 unit, etc.). ##236 [ TX / RX ] G3 modem control unit malfunction.

Solution: Boost the transmission level so the other party can receive the phase signal properly. Solution: If the other party is using a Canon model then contact them and have them match the passwords. A. We suggest you test the number by calling it from a land line to see if you get a fax tone.

Solution: Have the other party lower the reception level to prevent the other party from receiving echo signals. ##509 [ TX / RX ] Failed to detect end of Tonal Solution: Divide the job so that less than 31 document are sent at one time. Solution: Have the other party boost their transmission level to allow for proper phase signal reception. B.

The paper is not correctly loaded and the document sensor cannot sense it. Remove jammed originals, and then place them again. Remove the jammed paper. Retry the transmission.

Solution: Replace the board containing the BJ controller. No remote fax device The Fax number provided does to give a fax tone when answered. Solution: Have the other party boost the transmission level to receive picture signals properly. Solution: Set the document and have the other party call again F.

Error Code(s) Definitions/Causes Solutions 386 387 388 389 390 391 392 393 394 395 There is too much noise on the line for a valid connection between two fax machines to Error Code(s) Definitions/Causes Solutions 300 The fax session completed without errors. Turn both the sending and the receiving machine off for ten seconds, turn them on, and then try sending again. Solution: Record the protocol on DAT tape and then request the Canon Technical center to analyze the information. ##114 [ RX ] RTN was transmitted during reception.

Disable ECM, and then try faxing again. 382 ECM The remote fax machine held the local fax machine from continuing the ongoing transmission because of a temporary low memory condition at A. Cause: SCNT PWB Solution: Trouble-shoot according to Service manual. Cause: Abnormal protocol.

Cause: Thermistor trouble. There was an error while generating the document. Cause: Line noise. A.

A. A. Solution: Replace SCNT. ##222 [ RX ] 90% compression recording crystal breakdown. The click, heard for an incoming call, is actually a momentary disconnect of the line.