fatal error cannot read ip configuration win98 Hulett Wyoming

Address 34 10th Ave, Belle Fourche, SD 57717
Phone (605) 569-3062
Website Link
Hours

fatal error cannot read ip configuration win98 Hulett, Wyoming

Bill Worried19, Sep 15, 2004 #10 Sponsor This thread has been Locked and is not open to further replies. Double-click Network, and then verify that TCP/IP is installed. So how do I get my dial-up network adapter back? There is no tcpip.sys file located in the c:\windows\system directory.

Stay logged in Sign up now! Or sign in with one of these services Sign in with Facebook Sign in with Twitter Sign Up All Content All Content This Topic This Forum Advanced Search Articles Browse Forums Then I played with File Sharing in Win98. All rights reserved.

Andrews·DIRECTV·Pickwick Cablevi..

Bubba MVM 2003-Sep-16 10:25 pm said by Locutus65:In the microsoft article it shows all the locations of the Winsock2 keys in the registry. I did find THIS Microsoft Knowledge base article. Add TCP/IP back in again 5. wxp and wxp-laptop access internet.

In Control Panel/Network, if you are not on a network and connecting thru a local ISP, then the following should be installed: TCP/IP Dial-Up Adapter Dial Up Adapter Also under Primary Should I reload Win98SE?? Select the Windows Setup tab, double click on Communications and remove the check mark from Dial-up Networking. Bob Cerelli, Sep 15, 2004 #7 JSntgRvr José Moderator Malware Specialist Joined: Jul 1, 2003 Messages: 18,524 Nice site for information, Bob.

New Posts NY in February Latest: MongGrel, Oct 15, 2016 at 10:20 AM Off Topic PSA: The Eagles planned for Kennedy Center honors in January Latest: Squisher, Oct 15, 2016 at Reboot 3. I believe that my TCP/IP is conflicting with my drivers. If the IP address is still not renewing, then reinstall TCP/IP   Gets a valid IP address, but still has no network connectivity Reboot the computer Run winipcfg and see if

Also the second method typically requires the network drivers if they are not part of the original source code. To start viewing messages, select the forum that you want to visit from the selection below. http://www.onecomputerguy.com JSntgRvr, Sep 15, 2004 #8 Bob Cerelli Joined: Nov 2, 2002 Messages: 22,468 Thanks. Then try Winipcfg or Ipconfig thru the start run command. 0 Share this post Link to post Share on other sites Go To Topic Listing Windows 98 All Activity Home Operating

I also could not extract it from the windows disk as it is not there.So you do not feel like the Lone Ranger....I do not have a tcpip.sys in Win98 SE TCP/IP is there and is bound to my D-Link adapter, and there aren't any other adapters (now) for it to be bound to. I have XP Home unopened, should I try that? Code on a generator hook up? [HomeImprovement] by Corehhi338.

wxp and wxp-laptop see each other on network, but w98 can't access network or be seen by the others. Stay logged in Search titles only Posted by Member: Separate names with a comma. Remove any TCP/IP protocols that aren't bound to the ethernet card (i.e. Tech Support Guy is completely free -- paid for by advertisers and donations.

Worried19, Sep 11, 2004 #1 Sponsor MFDnNC Joined: Sep 7, 2004 Messages: 49,014 http://support.microsoft.com/default.aspx?kbid=286748 MFDnNC, Sep 11, 2004 #2 Worried19 Thread Starter Joined: Aug 8, 2003 Messages: 170 Thank Want IPv6? No, create an account now. Nothing seems to work.I do wonder though, the Winsock 2 update, works with 98se?One other thing I forgot to mention.

Make sure they have registered their computer with CampusNet. Worried19, Sep 15, 2004 #5 JSntgRvr José Moderator Malware Specialist Joined: Jul 1, 2003 Messages: 18,524 Go to the Add/Remove Programs icon in the Control Panel. I then would re-boot into safe mode....go into Settings\Control Panel\System\Device Manager and remove any entries that may or may not be in the Network Adapters. After installing the patch run winipcfg and release/renew the adapter.   Cannot release/renew IP address and has non-jmu IP address Open the network control panel and view the TCP/IP properties for

B: If you think your networking is corrupted 1. If there are any others that exist in other folders, then rename the files from "filename".dll to "filename".old. JamesM #1 JamesM3M5, Jul 6, 2003 JamesM3M5 Senior member Joined: Jul 2, 2002 Messages: 218 Likes Received: 0 Hold on a second, I found this: http://support.microsoft.com/default.aspx?scid=kb;en-us;286748 Good Lord! Thread Status: Not open for further replies.

Thread Status: Not open for further replies. {{offlineMessage}} Store Store home Devices Microsoft Surface PCs & tablets Xbox Virtual reality Accessories Windows phone Software Office Windows Additional software Apps All apps Windows apps Windows phone apps Games Xbox Release/Renew the IP address again. I think it would be easier to reinstall Windows.

Used it earlier when BellSouth was helping me to get my w98 to connect to the internet, and it worked. Add it back in again when prompted 4. I don't think it's related, but now I can't access the Internet, and I don't have an IP address on the laptop. Repeat the process above except the this time around click on Dial-up Networking to return the check mark to Dial-up Networking.

I realize now that I did a very stupid thing.