f35 error code kenmore elite Fort Washakie Wyoming

Address 242 Main St, Lander, WY 82520
Phone (307) 332-3707
Website Link http://colyersoft.com
Hours

f35 error code kenmore elite Fort Washakie, Wyoming

CST Sat 7:00 a.m. - 9:00 p.m. Got a F 35, Suds and F20 error codes. Inspect the vacuum hose first before replacing the sensor. With the washer unplugged, check the connection of the air pressure tube to this component.

neptunewaxmotorcom 12,923 views 10:39 New and Improved. you will see also see a little connector with four or five wirers. Can you give me some guidance as to removing this module?2. Remove the screws at the very back of the top panel and then pull it back slightly and then up and off of the washer.

I read that the pressure transducer is supposed to read from 1 to 5V. Take a moment to read as it fixed my sensor! Mark T , January 19, 2011 thank you for the reply. Thanks 07/19/2011 by mayer Add a comment 0/1024 Cancel Post comment Are you sure you want to delete this zzzzzz?

Loading... Thanks Randy! Posted January 08, 2011 Answers Barbara H. , January 08, 2011 i can understand the desire to take care of the cause for an error code before calling for service. Sorry, we failed to record your vote.

can the sensor be cleaned, repaired or reset without technician? sooo i have to buy a main control panel? I just went through the same issue and am very much pissed about it, because i just bought this washer (KENMORE ELITE HE5 STEAM) 6 month ago and am washing only If you are able to unplug the washer and check this air pressure tube, you may be able to resolve this problem.

Three years ago when I did this it took longer but this time it was easy -- a ten minute fix with most of that time fiddling with the harness.This time, I read that the pressure transducer is supposed to read from 1 to 5V. to make sure the switch is the problem. Would you repair kit still work for me?

If not, then it could be your CCU causing the issue. While I don't like the HE detergent , apart it is very expensive and my clothes actually smell bad, like petroleum; I use just simple the powder detergent. Yes No Voted Undo Score 1 Cancel Add a comment 0/1024 Cancel Post comment Are you sure you want to delete this zzzzzz? If excessive suds is causing the problem then it must be clogged or dirty.

FYI- blowing out the hose didn't work for me either. Check another model This fits your: Check another model See all parts that fit We're not sure this item fits your: Check another model See all parts that fit Partfinder Feedback The reading on this one was 1.21V. If the problem still exists after replacing this component, then the main electronic control board for the washer will need to be replaced.

Color red white white white Item Dimensions 2 x 4 x 2 in 2.5 x 1.5 x 3.5 in 6 x 10 x 9 in 4 x 4 x 4 in You can see bearing and seal kits for other washers at washer bearings. can the sensor be cleaned, repaired or reset without technician? Share it! August 20 by Priscilla Kennedy Show 6 more comments Add a comment 0/1024 Cancel Post comment Are you sure you want to delete this zzzzzz?

I have tried the CRC and it didn't work. I would suggest giving this a try! 08/09/2015 by Sharron Finally met an honest repairman! Cancel Randy Lopez Rep: 49 1 Posted: 06/23/2015 Options Permalink History I finally identified the root cause of my F35 SUDS error. You can find your product's model number on a plate affixed to the product or in the owner's manual.

ApplianceVideo.com 195,001 views 8:11 Whirlpool WasherDuet Repair F20 Error Code - Duration: 7:00. All you need is a low power (25 watt or so) soldering iron. I did what one forum suggested to make sure the pressure hose was clear. Was this answer helpful?

Loading... Hazel, October 20, 2012 Thank Alina but I cannot see the links that you referred to. Luckily the new pressure switch fixed the error, and removing that sock also made a big difference in how well the laundry was getting cleaned. Valid for standard ground shipping within the continental United States and not valid for shipments to Alaska, Hawaii, Puerto Rico, Guam and the US Virgin Islands.

or Add to List Sorry, there was a problem. Water vapor from the tub makes its way through the rubber tube and collects on the sensor in the diaphragm causing the error code f-35 or suds (it thinks your tub Thanks so much for this site and the time people take to help out others. The new shipment of these parts was supposed to arrive 7/18/2011.

See http://www.washerbearings.com.Don’t forget to subscribe and leave any questions below…Thank you,Jeff Hartman“The Neptune Man”P.S. I knew that I wasn’t going to get anywhere with her so I escalated to her manager “Austin”. “Austin” tried or said he tried to find the part from a couple Yes No Voted Undo Score 1 Cancel Add a comment 0/1024 Cancel Post comment Are you sure you want to delete this zzzzzz? it would slide upwards for about a half inch but i couldn't get it to come off the wall of the washer. 1.

Cancel Randy Lopez Rep: 49 1 Posted: 07/16/2014 Options Permalink History I was able to repair my failing pressure sensor by spraying a couple of short/light bursts of CRC QD Contact The F35 error indicates the Central Control Unit has detected a malfunction of the analog pressure sensor. I called a local repair service and found that I needed the “analog water pressure level sensor” which apparently had been discontinued by Whirlpool and replaced with a re-engineered part. 4.) The repairman suggested that we do this at least once a year!

Sign in 1 Loading... Yes No Voted Undo Score 1 Cancel Add a comment 0/1024 Cancel Post comment Are you sure you want to delete this zzzzzz? if you find a loose connection, secure the wire harness properly on the component then reassemble and test the washer. Now remove the short black rubber hose from the top of the pressure sensor chip.

My new LG washing machine will be here tomorrow, with a standard 10 year warranty which costs about $150 more than the replacement from Whirlpool.