frigidaire stove pf error Shepherdstown West Virginia

Address 276 Retail Commons Pkwy, Martinsburg, WV 25403
Phone (304) 262-5538
Website Link
Hours

frigidaire stove pf error Shepherdstown, West Virginia

Gene. This happens every time and we have used different oven thermometers in case one was defective. I still get the PF error in exactly the same spot, but if I run the water/service test it gets through all 8 steps without a failure now. Tip: The max point reward for answering a question is 15. 0 characters Video Photos Link Replacement Parts Add Upload Upload × × Draw a box over the problem!!

Please enter a valid email address. For now, I guess I'll remove all remnant melted plastic from the connectors to rule out a short inside that molten mess. John // Apr 8, 2015 at 7:28 am Here is the actual label on my stove. [IMG]http://i62.tinypic.com/4t7oyg.jpg[/IMG] Gene // Apr 8, 2015 at 2:04 pm Hello John, I did not question Gene.

Thank you in advance!! In such situation the only solution is to replace the EOC. Sign up here Find a Professional Type of Job Type of Job Additions and Remodels Appraisers and Home Inspectors Architects Bathroom Remodeling Cabinets and Countertops Carpentry Carpet Cleaning Concrete and Masonry The part number for the EOC is 316455410 The part number for the overlay is 316220725 You can view and order them by clicking on the part numbers.

It would need to be replaced. Thank you for your help. steve // Dec 1, 2014 at 11:20 am hi gene i have frigidaire range that keep giving f30 & f31 errors - i managed to reset by tripping the breaker but The part number for the porcelain wire nuts (pack of 10) AP3440631 Good luck.

If you would order the part from AppliancePartsPros.com by clocking on the part number I posted, you have nothing to loose. What should I do? steve // Dec 2, 2014 at 11:44 am hi gene PLEFMZ99ECC used to get f30 but now getting F7 12 and the front element wont turn off - any ideas ? Good luck.

You may want to call AppliancePartsPros.com customer service at 1-877-477-7278 to find out the ETA. Gene // Jan 3, 2015 at 7:48 pm Hello Sharon, Sorry for the delay. Now the convection fan stays on and it throws a F30 error code. Give me the model number on the unit also and just back with me later.

Gene. I would appreciate any you can provide! The good part of this sad news is that you got nice opportunity for a good New Year (or may be it's not too late for Christmas?!) present to your wife If the reading is incorrect, the temperature sensor would need to be replaced.

You may want to start the troubleshooting from testing the temperature probe resistance. Thank you in advance, Steve Gene // May 16, 2015 at 6:25 pm Hello SteveB, You may want to check the wires between the temperature probe and the EOC. If there is no continuity, the heating element is the culprit. Reply With Quote May 22nd, 2013,06:21 PM #6 rickgburton View Profile View Forum Posts Appliance Tech - Moderator Join Date Jul 2006 Location Murray, Utah 84107, United States Posts 24,368 OK,

Remove the rear panel and locate the relay board. You can get them in a hard ware store or order from AppliancePartsPros.com by clicking on the following part number. If you ordered the EOC and the temperature sensor from AppliancePartsPros. I can press clock to reset the clock and it seems to take the PF code of the display until the next time I use my oven and it goes into

Thank you for stopping by. George Gene // Dec 19, 2014 at 1:01 pm Hi George, You are welcome and thank you for the feedback. I worked as an appliance tech for 13 years just to let you know my qualifications on repair (3 for Frigidaire corp.) I am very frustrated with this Frigidaire range as This can be either circuit breaker or fuses.

Gene. Thus if any of them failed, the whole heating element would need to be replaced. You can get it from AppliancePartsPros.com for $558.91. In order to provide most accurate advise I need the complete model number of the oven.

Sounds like the EOC is the culprit. I managed to push them back into the cap, and we were able to reconnect it to the EOC board, but at least one of them broke off. Locate the P5 connector at the EOC and remove two violet wires from pins 12 and 13. I do know that PF stands for “power fail”.

Thanks again and happy New Year! I do have several boards. Gene. The temperature sensor part number 316217002 The relay board part number 316429800 This part is on back order.

Now that seems common, but here is where the strange part comes in, the beeping and error. It is giving F11 error. Try to push cancel and then push clock and set the clock. I replaced the clock and the burners worked but the clock would not clear the PF code.

I have spent lots of time researching my issue and can not find anyone else describing this particular problem. Keep me posted. Attached Images 01-08-13,10:13 PM #3 flapus007 Member Join Date Jan 2013 State AZ Posts 2 Thanks so much for your reply. Just in case you will decide to get new control panel, the part number for the control panel is 316538405 Good luck.

Thanks. Gene. Valerie // Sep 7, 2015 at 8:00 am Hello again Gene! There are no a separate keyboard or keypad on your range.

I checked the resistance on the probe's bare wires and it reads 1099 ohms. The part number for the EOC is 316557115 The part number for the latch motor assembly is 316464300 Good luck. Get blinking clock on EOC and "PF" suggesting power failure. Remove the power to the range by turning off the corresponding circuit breakers prior to do any job.

In such situation you may want to check the wires from the EOC to the temperature probe to make sure there is nothing wrong.