frigidaire classic series stove f1 error Shanks West Virginia

Dentists, Tooth Whitening

Address RR 50, Capon Bridge, WV 26711
Phone (304) 856-2234
Website Link
Hours

frigidaire classic series stove f1 error Shanks, West Virginia

What should I focus on next? The cause of this error code can be a faulty door lock assembly or a faulty EOC. The electronic oven control board initially displays F10 for this condition. The infrequent nature of the problem can make it a bit more difficult to locate the failure, but if we put the signs together, (and read the tech sheet) we can

Thank you for your question. This seems to have happened randomly after years of fine operation. Locate the two pins in the plug at the EOC that are connected to the sensor. To access the module, you have to remove the back panel from the range.

This too was about right so I concluded the temperature probe was working fine, leaving the control board as the cause of these intermittent fault codes.I attempted to start and stop My range is a CEW30ef6gsc. Ken // Dec 24, 2014 at 4:00 pm Gene, Merry Christmas. Keep me posted.

Thanks again and merry Christmas! It can be easily determined by the model number, usually located on the frame behind the bottom drawer or on the oven door frame. I managed to push them back into the cap, and we were able to reconnect it to the EOC board, but at least one of them broke off. The part number for the oven relay board is 316443920 The part number for the EOC is 316576601 Good luck.

Could the EOC be bad again or is there something else I should look at? I have a frigidaire oven model FGF379WJC, and when I select any button on the oven control panel it displays, "OFF". Most likely there is only one problem caused by the faulty EOC, but there is a very small chance for the latch motor to fail as well. Good luck and Happy Holidays.

Frank // Nov 4, 2014 at 3:56 pm I have an Electrolux model#EW30DF65GSB. Step 5 Transfer the wiring harnesses from the old module to the new module—one at a time—to ensure they go to the same places on the new module. Virginia Beach, VA "Your service people are so friendly and helpful. If fault returns when power is reconnected, continue the troubleshooting.

To adjust the oven temperature higher 1. Related Searches Read Article Make an Ikea Lack Table Look Expensive With This Cheap Hack You May Like How to Replace the EOC on a Frigidaire How to Reset a Frigidaire I am confused if it's the EOC or if there could be a problem with the oven relay board. Thanks for your help Gene // Apr 23, 2015 at 10:12 pm Hello Jeff.

Try the bake or broil feature once more, and if the error code repeats, unplug the appliance and wait five minutes before plugging it back in. Returned all the wires to their original locations and put everything back together. You can change this preference below. Good luck.

You may want to replace it as well. Hinzufügen Möchtest du dieses Video später noch einmal ansehen? My question is this, would that be the main culprit? There should be a steady increase or decrease in the measured resistance as the shaft is turned.

I was out of town. Thanks again. What can I do to open the door and reset the oven? Unable to proceed the request.Please try again © 2016 Sears Brands, LLC Privacy policy California privacy policy Careers Product recalls Terms of use Hide for questions or assistance, call1-888-206-3625 (Se Habla

Login|Contact Us Appliance Need Appliance Repair Help? Logged TechnicianBrianwww.TechnicianBrian.comwww.AllTechAppliance.com jb35007 VIP Member Member Since: Feb 2014 Posts: 4 Re: Frigidaire Range F1 Fault Code « Reply #1 on: June 24, 2015, 09:24:30 AM » i have a frigidaire The cause of the problem in such situation most likely is a failed wire harness between the sensor and the EOC. Prev123456789Next » Not finding what you are looking for?

To increase the temperature use the number pads to enter the desired change (Example 30°F) 3 0. There are two different potentiometers with the ESEC control system. Still not working but the igniter fires up now. I REALLY NEED IT FIXED Gene // May 19, 2015 at 11:05 pm Hello Christy.

It's self-adhesive and if it can not be safely removed from the old EOC and properly attached to new part, you may want to order the overlay as well. There are a few potential causes for the F1 code, depending on which boards and touchpads are used. I was able to use it a couple times after but the cooking times varied between a little slow and A LOT slow. Parts cat.

Usually an hour or so after it has been shut off. All of our chat agents are currently assisting other customers. Wire nuts (pack of 10) AP5641944 Good luck and keep us posted. See Details Frigidaire FFEW2425QB 24'' Single Electric ...

Gene // Dec 21, 2014 at 12:39 pm Hello James, Unplug the range or turn off the range circuit breaker for a few minutes and reapply power. I placed my order for the needed EOC today. Unfortunately the only solution to fix it is to replace the EOC. Check the temperature sensor resistance as described previously.

Both probes check 1178-1179 OHMS at the probe and the board. Sorry for the delay. F11 - Shorted keypad. It would need to be replaced.

Learn More guaranteed fit All parts are manufacturer-approved, to ensure proper fit and to keep appliances running for years to come.