fp error tektronix Reynoldsville West Virginia

Technical Support Troubleshooting

Address 126 Thompson Dr, Bridgeport, WV 26330
Phone (304) 695-7021
Website Link http://www.techlandwv.com
Hours

fp error tektronix Reynoldsville, West Virginia

Generated Sun, 16 Oct 2016 00:57:06 GMT by s_ac15 (squid/3.5.20) and84■If problem persists, check www2.tek.com/merlin/tko and/or contact Service. The killer feature was the real time sample rate which supports the full oscilloscope bandwidth.At the time CCD digitizing systems were an order of magnitude faster than using a fast converter Turn the printer off, then on. ■ Replace Imaging Unit.

I replaced the address decoding logic that generates the ROM CS signals, on the theory that this is the only thing unique to the individual ROM slots, but no change.Why this I put a logic probe on it, and the FPP was returning a high on one of the lower four data lines, which are required to be all low.Reading through the Tektronix does not regularly monitor posts in this area. After the supply refurb and a very good clean to remove the considerable dirt build up it seemed to work and passed all start up tests.

Turn the printer off, then on.  ■ Replace Imaging Unit (make sure that Imaging Unit is locked in place). It will say "Front panel not responding". Waiting For Transparency The print job specifies transparency, but the printer detects that the paper tray is installed. Leakage from the caps got under the op-amps and had enough conduction to cause errors in the signals.

Replace Media Tray Insert the standard media tray. Now that you mention it, one mode of fallout due to the corrosion could have been RAM and data buffers fighting on write cycles.Perhaps it's worth putting the logic probe on Hide thumbs Also See for Phaser 300X User manual - 4 pages 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 If you want to continue cleaning and purge more ink, press the button again; otherwise the message clears in 10 seconds.

Watch these Pics: http://forum.iwenzo.de/sonstige-reparaturtipp... Error messages, such as Jam:Open Front Cover, require you to perform some action, such as clear a paper jam. Advanced Features and Troubleshooting Manual93 4 TroubleshootingError codesIf the printer’s front panel displays a message Error XX, find the error code in this table and follow the instructions for resolving the The 420 and the 460 are terrible about that particular failure.

From looking at the data lines under kernel test, they do look OK, e.g. They can definitely be damaged by over current conditions.QuoteAny practical difference between the ROMS/RAMs? Turns out it's all digital display, although the details are still pretty fascinating to me. Thanks,DarrenBoise, Idaho Top Post Reply Print view 1 post • Page 1 of 1 Return to “Other or Discontinued Oscilloscopes” Jump to Customer Support Product Support Oscilloscopes

For some reason this was true for both 50Ohm contact pads, but only for one 10X attenuator. I believe the corrosion eventually penetrated the battery and caused it to spill it's guts.Now all the POSTs are failing except for ROM and WP. and Canada at 1-800-835-6100 or on-line at http://www.tek.com/Color_Printers/. Teodoru Targu-mures, Romania #10 Feb 22, 2009 Ken Feldhaus wrote: I have a TDS420.

You may need to clean the paper exit path if the problem persists. The non-real time 2252 does not really count and I suspect that is as good as they could have done in the 2465 form factor.Any DSO can support a full pre-trigger Load paper in the media tray and press OK. Try cycling power on the printer.

Using those CCDs for capture and storage, then digitizing at a much lower rate seems like a pretty scrappy thing to do.I guess the killer feature of this scope at the Waiting For Paper The print job specifies paper, but the printer detects that the transparency tray is installed. I passes all tests but it says TEK Running:OFF. Logged siggi Regular Contributor Posts: 153 Country: Re: Attempting to repair a Tektronix 2430 « Reply #21 on: April 24, 2014, 04:33:16 AM » I pulled the main board out

Turn the printer off, then on. ■ If problem persists, checkwww2.tek.com/merlin/tko and/or contact Service.  Error 74■ Remove andre-installFuser. Thanks for your comment! Reply » Report Abuse Judge it! Open the top cover and make sure the bottom ink sticks are resting against the bottom of the ink bin chutes.

This is what I did during initial cleaning - the coax had wicked some of the corrosion gunk out to the main board, so I pulled it and cleaned it. Tektronix News Forums Not a Topix user yet? Maybe this is more fallout to the water/corrosion damage. Go to the WindowsPostScript tab and uncheck the boxPrint PS Error Info.

Turn the printer off, then on. ■ Replace Transfer Kit. Presumably something resulting in failures across registers, system RAM and the FP is pretty central, so ought to be easy (famous last words) to find.Alternatively if the GPIB is functional, apparently To print the manual completely, please, download it. Here is an answer I got from a seller on ebay:"There is about 30 electrolytic caps on the acquision board.

Question: Why do I get an error message saying Front Panel Not Responding after updating to version 3.2? I have a TDS644a that had the Acc error. Still, menus and stuff!After multiple cold boot and self cal cycles, I'm past the NVRAM CRC failures, but I'm still failing all 7/8/9000 tests except CCD efficiency. Don't show me this message again.

Sign up! Tektronix Prism and SPG8000A Support Ibc TV Liv... Turn the printer off, then on. ■ If problem persists, checkwww2.tek.com/merlin/tko and/or contact Service.   Error 63■ Remove andre-installImaging Unit. Error messages, such as Jam:Open Front Cover, require you to perform some action, such as clear a paper jam.

Be polite. I found that the board must be thoroughly cleaned. There are, however, also a couple of socketed chips on the readout board that I haven't touched. Post Reply Print view Search Advanced search 1 post • Page 1 of 1 Wayfarer Posts: 10 Joined: January 8th, 2012, 10:20 pm TDS310 bad front panel module - what should

Turn the printer off, then on. ■ Remove andre-installTransfer Kit. I'll be very interested in seeing what you track down. Refer to the table below for responses to front panel error messages. I messed up both attenuator and preamp on channel one to learn this.

An incorrect paper size is loaded in the tray, or paper narrower than A4-size is in the manual feed slot. Remove the paper jam. Also pulled the front panel switch board, which is all crusted with gunk. I am sure you could substitute one for the other.I suspect the preamplifiers are the same as well but there are part number errors in the 2465B documentation so I am

Poking around the Rom area seemed to make a difference so I removed the IC's and reseated in the sockets and all is good again.