fanuc rj3 error codes Hendricks West Virginia

Address 706 Beverly Pike, Elkins, WV 26241
Phone (304) 636-3100
Website Link
Hours

fanuc rj3 error codes Hendricks, West Virginia

Very useful.Edit: Hey it got stickied! If it has, reset the robot and jog-feed it to recover from the collision. The OVC alarm is issued based on this estimated temperature. Stand up and express the divinity within you--Swami Vivekananda Godfather Newbie Thank You -Given: 1 -Receive: 0 Posts: 4 Re: A website: Know FANUC alarm codes « Reply #7 on: December

o (Action 2) Check the switch and cable connected to 3 (FENCE1) and 4 (FENCE2). Newletter About Terms DMCA Contact STARTUP - Share & Download Unlimited Fly UP 1 Hour 1 Day 1 Week 1 Month Forever Login with username, password and session length News: Welcome The OVL alarm occurs when each built-in thermal relay detects a temperature higher than the rated value. o (Action 1) Replace the panel board.

Select SYSTEM.  3. Are you sure you want to continue?CANCELOKWe've moved you to where you read on your other device.Get the full title to continueGet the full title to continue reading from where you The servo amplifier 7-segment LED indicates -. o (Action 2) Disconnect the motor power lines from the servo amplifier terminals, and check the insulation of each motor power line (U, V, or W) and the GND line.

Hokuryu Newbie Thank You -Given: 1 -Receive: 0 Posts: 6 Re: A website: Know FANUC alarm codes « Reply #8 on: December 11, 2015, 09:31:00 AM » Thank you! Check them and replace them if necessary. As a result, the motor becomes unable to follow the command, and an alarm is issued.) o (Action 3) Check each phase voltage of the three-phase power (200 VAC) input to Member Thank You -Given: 71 -Receive: 15 Posts: 287 Re: A website: Know FANUC alarm codes « Reply #10 on: December 17, 2015, 02:24:30 AM » good job Logged KUKA Conntroller

See the description about the PHAL alarm (SRVO-064). (64) SRVO-087 WARN BLAL alarm (Track enc : i) o (Explanation) This alarm occurs if the voltage of the backup battery for the Logged FANUC --> ABB --> KUKAProgramming for PC / web sometimes. o (Action 1) If the ambient temperature is higher than specified (45 C), cool down ambient temperature using the air conditioning unit. If it is bad replace it. (Action 3) Replace the cable between the emergency stop board and the magnetic contactor. (Action 4) Replace the emergency stop control PCB. (Action 5) Replace

In this case, the position data will be lost. Robotforum | Support for Robotprogrammer and Users Industrial Robot Help and Discussion Center Fanuc Robot Forum (Moderators: Sven Weyer, !2Sharp, Lerak, Napierian) R-J3 SRVO-156 Error on power up - get on o (Action 2) Replace the teach pendant. The alarm condition occurs if the magnetic contactor turns out to be already on when an attempt is made to turn it on.

If it is necessary to run the robot by short-circuiting the signal even temporarily, an additional safety provision must be provided.  (5) SRVO-005 SVAL1 Robot overtravel o (Explanation) The robot o (Action 1) If this alarm occurs together with the PHAL alarm (No. 064), this alarm does not correspond to the major cause of the failure. o -If this alarm occurs before the magnetic contactor is turned on: o (Action 1) Check each phase-to-phase voltage of the three-phase input (200 VAC) on the primary side of the o (Action 1) Hold down the shift key, and press the alarm release button to reset the alarm condition.

o (Action 2) Check the overtravel connection cable (one-piece i -cabinet/robot type) and robot connection cable (RP1) for a ground fault. The system returned: (22) Invalid argument The remote host or network may be down. If the input is not higher than 170 VAC, check the input power supply voltage. Common Trouble ChecklistIs your computer plugged in?Have you checked all the cords?How about other connections?Unseated cardsDo you have… Preventive maintenance and troubleshooting Motor Troubleshooting and Maintenance Maintenance and Troubleshooting of

Usedrobotstrade.com 2. o (Action 3) If the thermostat on the main board is defective, replace the backplane unit.  (11) SRVO-018 SVAL1 Brake abnormal o (Explanation) An excessive brake current is detected. o (Action 3) This alarm occurs also if the emergency stop line was broken, but the software failed to identify the cause. The motor might not be hot even if the OVC alarm has occurred.

WARNING Do NOT short-circuit, or disable, this signal in a system in which the External emergency stop input signal is in use, as it is very dangerous. NOTE This alarm might accompany the DTERR, CRCERR, or STBERR alarm. o (Action 2) Check that the load weight is within the rating. o (Action 4) Replace the Main Board.  (2) SRVO-002 SVAL1 Teach pendant E-stop o (Explanation) The emergency stop button on the operator's Teach Pendant was pressed.

o (Action 1) This alarm may occur if the axis is subjected to frequent acceleration/deceleration or if the axis is vertical and generates a large amount of regenerative energy. Course Type This is an instructor led course… Hydraulic Maintenance and Troubleshooting Troubleshooting hydraulic systems: methods for better understanding and enhanced performance. (CMA/Flodyne/Hydradyne) Drive for Technology 2010 Troubleshooting and maintenance fundamentals If the peripheral device are normal, check the robot cable and if the peripheral device are abnormal, replace the device. o (Action 2) Check to see if the load is greater than the rating.

If it is 170 VAC or lower, check the line voltage. o (Action 2) Replace the servo amplifier.  (9) SRVO-014 WARN Fan motor abnormal o (Explanation) A fan motor in the backplane unit is abnormal. Generated Sat, 15 Oct 2016 15:01:50 GMT by s_ac15 (squid/3.5.20) ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.7/ Connection If the measured three resistances are different, the motor, robot connection cable, or robot internal cable is likely be defective.

Your cache administrator is webmaster. o (Action 1) Check the three-phase input voltage at the servo amplifier.