fabric error-recovery fabric-switchover Gilbert West Virginia

Address 30 Elkhorn St, Welch, WV 24801
Phone (304) 436-4337
Website Link
Hours

fabric error-recovery fabric-switchover Gilbert, West Virginia

Table1 Valid type Values Keyword Definition gigabitethernet Gigabit Ethernet IEEE 802.3z interface. The fabricbuffer-reservequeuecommand is supported on Cisco 7600 series routers that are configured with the following modules: WS-X6748-GE-TX WS-X6724-SFP WS-X6748-SFP WS-X6704-10GE Entering the defaultfabricbuffer-reservequeue command is the same as entering the fabricbuffer-reservequeue To disable truncated mode, use the no form of this command. Back Products & Services Products & Services Products Identity and Policy Control Network Edge Services Network Management Network Operating System Packet Optical Routers Security Software Defined Networking Switches All Products A-Z

This command is supported on DFC-equipped modules and the supervisor engine only. If you enter the nofabricrequired command, the modules will also power on if a Switch Fabric Module is not present and the configuration allows for it. module num (Optional) Specifies the module number. switch num (Optional) Specifies the switch to access; valid values are 1 and 2.

If grants are not received within a certain period of time, a destination timeout is declared. Examples The following example sets the timeout timer to 200 ms: Router(config)# interface fddi 0 Router(config-if)# fddi t-out 200 Related Commands Command Description fddi c-min Sets the C-Min timer on the Usage Guidelines The EtherChannel load distribution algorithm uses a register (the bundle select register) in the port ASIC to determine the port for each outgoing packet. fabric buffer-reserve [ high | low | medium | value ] [default] fabric buffer-reserve queueno fabric buffer-reserve Syntax Description high (Optional) Reserves the high (0x5050) ASIC buffer spaces.

The default interval is 120 seconds. clear mls statistics (virtual switch) To reset the MLS statistics counters, use the clear mls statistics command in privileged EXEC mode. Usage Guidelines Use the frame-relaypayload-compression command to enable or disable payload compression on a point-to-point interface or subinterface. Are the commands above feasible?

bit 7--Link confidence test failed. Reply Fernando Ipar says: July 31, 2014 at 9:30 am @Tim: A proper answer to these questions requires a blog post on its own, not just for the length of the The fabricswitching-modeallow c ommand affects Supervisor engines that are configured with a minimum of two fabric-enabled modules. If the control board is turned offline by specifying the request chassis cb slot slot-number offline or a pressed physical button to cause a graceful shutdown, a fabric failure does not

Examples This example shows how to set the global port deferral interval to 60 seconds: Router(config)# port-channel load-defer 60 Router(config)# This example shows how to verify the configuration of the port The mode change occurs as the modules come up after the power cycle. interface Specifies the facility alarm for interfaces. Please do not ask me again.

Command Default 3 buffers Command Modes Interface configuration Command History Release Modification 10.0 This command was introduced. 12.2(33)SRA This command was integrated into Cisco IOS Release 12.2(33)SRA. I am looking forward to the recorded webinar : ) Reply Tim says: July 31, 2014 at 8:40 am I set up an HA group with two MySQL server A and Features Order Support Screenshot Getting Started Knowledge Base CISCO-CAT6K-CROSSBAR-MIB. The default is 30.

Usage Guidelines This command applies to the FCI card only. Cisco 2600 Series and Cisco 3600 Series Routersfdl { att | ansi | all | none } no fdl { att | ansi | all | none } Cisco 10000 Series To configure multicast NSF with SSO parameters, perform this task: Command Purpose Step1 Router# configure terminal Enters global configuration mode. standby-sp Specifies the standby switch processor.

From that point on, you can use the connectors as described, and the mysqlfabric utility to manage the Group too. Examples The following example shows how to enter the module provisioning configuration submode: Router(config)# module provision switch 2 Router(config-prov-switch)# These examples shows how to configure module provisioning: Router(config)# module provision switch After multicast routing protocol convergence has taken place, the shortcuts downloaded by the newly active route processor (RP) will be merged with the existing flows and marked as new shortcuts. Then enter one or more lines of text, terminating the message with the second occurrence of the delimiting character.

Note OSPF NSF requires that all neighbor networking devices be NSF-aware. To obtain predictable results, follow these guidelines: Use sendon only when remote ports are set to receiveon or receivedesired. The switch requires between 0 and 3 seconds to switchover from the active to the redundant supervisor engine. If all other modules are operating in dCEF mode, module OIR is non-disruptive.

Support in a specific 12.2SX release of this train depends on your feature set, platform, and platform hardware. Examples The following example shows how to allow a list of modules to use the SPAN servicemodule session: Router(config)# monitor session servicemodule switch 1 module 1-2 Router(config)# The following example shows When you insert or power on the first Switch Fabric Module, the modules that were previously powered down power up if the Switch Fabric Module configuration is not in conflict with Command Default microseconds : 2500 Command Modes Interface configuration Command History Release Modification 10.0 This command was introduced. 12.2(33)SRA This command was integrated into Cisco IOS Release 12.2(33)SRA. 12.2SX This command

The table below describes the command tokens. off Prevents a local port from receiving and processing pause frames from remote ports or from sending pause frames to remote ports. Examples The following example shows Frame Relay configured to use payload compression with the frf9 stac algorithm for CAIM hardware compression, using the installed data compression AIM daughtercard as the compression Command Default Disabled Command Modes Global configuration Command History Release Modification 12.2(17d)SXB1 Support for this command was introduced on the Supervisor Engine 720. 12.2(33)SRA This command was integrated into Cisco IOS

Step4 Router(config-router)# nsf interval [minutes] (Optional) Specifies the minimum time between NSF restart attempts. Examples This example shows how to enable a fast-redirect optimization on a Layer 2 multichassis EtherChannel: Router(config)# interface port-channel 4 Router(config-interface)# mls ip multicast egress fast-redirect Related Commands Command Description show Examples The following example shows how to specify truncated mode: Router(config)# fabric switching-mode allow truncated Related Commands Command Description ipv6 mfib hardware-switching uplink Configures MFIB hardware switching for IPv6 multicast packets If you first configure a SPAN session with a source interface, and then try to add a source VLAN to the same SPAN session, you get an error.

Command Default milliseconds : 100 Command Modes Interface configuration Command History Release Modification 10.0 This command was introduced. 12.2(33)SRA This command was integrated into Cisco IOS Release 12.2(33)SRA.