fanuc dc error Heisson Washington

Address 401 NW 277th Cir, Ridgefield, WA 98642
Phone (360) 727-3035
Website Link http://www.yext.com/p/citysearch/converged-is-ridgefield-washington.html
Hours

fanuc dc error Heisson, Washington

Logged Racermike123 Hero Member Thank You -Given: 3 -Receive: 129 Posts: 672 Re: SRVO-136 error DCLVAL Alarm....Plz HELP!!!!! « Reply #6 on: January 29, 2014, 07:17:12 PM » There is a How does one test a spindle motor? Check 5v fuse. I checked the electronics, but the post POCOATO, he comments on grease on the actuator.

Check voltage on pins 1 and 2, and 2 and 3 on CNC2 for 19 volts ac. In a three phase system when two fuses blow the third one takes a hit too but may not blow. Need Proximity Tester? Those are fuses too.

It has been at least 20 years since the last time I touched a Fanuc DC spindle drive or motor or any DC motor on a machine tool. To enter another mode, first cancel the orientation command. Make sure you do not touch the lead tips of the meter or the metal on the fuse connections because you will be measuring your skin resistance of your fingers and A “9” would occur if the overcurrent was detected using the other drive circuitry in the amplifier and the fault would be caused externally from the drive.

Inductosyn/Resolver pcb is bad. Remedy Replace fan, review cutting conditions, clean parts. ER-03 The Cs contouring control command is input although bit 5 of parameter No. 4001 is set to 0 to specify that a high-resolution magnetic pulse coder is not used or Check the setting of the parameter for using the speed range switching control function, and the power line status check signal (RCH).

Get a cheap inline fuse holder at radio shack and solder in across the fused contacts. I don't recall seeing a Fanuc spindle drive with that appearance. OT 108 Voltage (+24V) Too High Check 24Volts, Check voltage selector switch OT 109 Power Semiconductor Overload Power semiconductor overheat Check Fan on spindle drive OT 110 Voltage (+15V) Both in .pdf format I could email.

If this is the case I will replace all three fuses. Pulse coder may be defective. After running a few parts without any issue the spindle alarm (94 with my Okuma lathe) illuminates. Fanuc CNC Control Models Applicable:16/18/21, 16i/18i/21i, 160i/180i/210i, , 0i Manufacturing | Industrial | CNC machinist | Maintenance | Repair | Machinery | BearingsFanuc 16/18/21 0i 16i/18i/21i 160i/180i/210i Add new comment 410

Privacy Policy 1 Hour 1 Day 1 Week 1 Month Forever Login with username, password and session length News: >> Robotexperts wanted !? << Robotforum | Support for Robotprogrammer and Hopefully, replacing the Daito fuses cures this problem. Reply With Quote Kevin77 liked this post 05-12-2014,09:36 PM #12 amdinc View Profile View Forum Posts Hot Rolled Join Date Mar 2010 Location N.E. These must be additions after the machine was produced because they look nothing like the diagram in the manual.

ER-24 In continuous indexing with orientation by a position coder, incremental operation (INCMD = 1) is first performed, after which the absolute position command (INCMD = 0) is entered. Remedy Replace parts, check connections, review cutting conditions. Check the parameter setting enabling the use of the orientation function. All rights reserved.

The CNC sends a run command to the spindle drive, the 7 segment display will switch to "00", the spindle motor will rotate. Check the parameter settings. Check for short circuit on transistors. Casting Metals Moldmaking Welding Brazing Soldering Sealing Mass finishing equipment/media/stratigies 80/20 TSLOTS / Other Aluminum Framing Systems Commercial Products Support Forums Automation Technology Products Taiwan How-Mau Machinery Co., Ltd Zapp Automation

OT 113 CPU Error Replace spindle board OT 114 Rom Error Rom ics defective. I can't seem to find any breakers or fuses popped in the cabinet. ER-18 When bit 2 of parameter No. 4001 is set to 0 to specify that a position coder signal is not used, orientation by a position coder is specified. Position Coder Detect 43 Disconnect PC for Dif SP Mod 44 Control Circuit (AD) Error 46 Screw 1-Rot Position Coder Alarm 47 Position Coder Signal Abnormal 49 High Conv.

Then email us to receive a Free CNC cheat sheet from the CNC Specialty Store! Before specifying absolute position commands in succession, perform absolute position command orientation. The motor power cables and TG cables should be tested for continuity and insulation integrity. To help us do this please fill in the contact form at the bottom of the page The details we would need are The part number of your Fanuc item The

Check the sequence. ER-24 In continuous indexing with orientation by a position coder, incremental operation (INCMD = 1) is first performed, after which the absolute position command (INCMD = 0) is entered. Reply With Quote amdinc liked this post 05-10-2014,07:33 PM #5 angelw View Profile View Forum Posts Titanium Join Date Sep 2010 Location Victoria Australia Posts 2,596 Post Thanks / Like Likes SPINDLE DRIVE PART NUMBERS, SPECIFICATIONS AND PCB PART NUMBERS Alpha Series Spindle Amplifier Modules (SPM) Type 1 New Specifications (Supporting Spindle HRV Control) CE Marked Products Model Drive type Main PCB

I did not replace the 3 fuses supplying the main power to the drive motor. REPLACE ALL CAPS, AND TRANSISTORS reply Comment viewing options Flat list - collapsedFlat list - expandedThreaded list - collapsedThreaded list - expanded Date - newest firstDate - oldest first 10 comments Once repairs are all done then put the proper fuses in so the alarm signal works. It is worth noting that when an alarm occurs on the Power Supply Unit, an alarm also appears on the Spindle.

Check for short circuit on transistors. Either bearings, axis brake, lubrication, counterballance weight ect. The manual indicates the 100A 3Phase fuse should also be replaced if the Daito fuses blow. Logged RoBoWi Full Member Thank You -Given: 4 -Receive: 15 Posts: 173 Re: SRVO-136 error DCLVAL Alarm....Plz HELP!!!!! « Reply #1 on: May 22, 2012, 11:33:54 PM » Check if the

Regards, Jade York Russell Thompson 9 months ago What does status d on my servo amp mean and how would i correct it Thanks Russell Joe 6 months ago In such a case, the motor is not activated.