general misprint error Weyers Cave Virginia

Address 41 Court Sq, Harrisonburg, VA 22801
Phone (540) 433-2952
Website Link http://drawbridgetechnologies.com
Hours

general misprint error Weyers Cave, Virginia

Same as 42 error. 49 FIRMWARE ERROR Only for the laserjet 4100: Try printing a different file if error persists remove all dimms and EIO devices, last replace formatter. 50 ERROR Then I heard them start turning again, and turning, and finally paper started coming out. Check tabs on side of toner cartridge. Replace DC Controller PCA. 2.

I kept getting 41.03.00 and 13.06 errors. A SIMM memory error occurred. 5Si/4000/4050/4100/5000/8000/8100 Only: X= Hardware type. 0: Rom 1: Ram Y= Hardware device. 0: Internal memory 1: SIMM slot 1 2: SIMM slot 2 3: SIMM slot It was difficult to understand through the accent, but the HP support tech thinks that either the fuser is not hloding the heat, or the sensors are reporting that the fuser Replace high-voltage Power Supply.

It has not messed with the document formats as of this time. Laser Malfunction See Error 51. 53.XY.ZZ Memory Error Cycle Power. It might be possible for the intercommunication between the two to get in a tangle but it should recover with a power cycle. II, IID Only: 1. 53 Error - Replace memory card.

I am waiting to hear from the users if they experience any interruptions. Need help? Note IIISi/4Si: Short cp005 on DC Controller to bypass Error 50 time delay. (The printer must be turned off.) 5Si/4000/4050/4100/5000/8000/8100 Only: The fuser is malfunctioning. 50.1 Fuser low temperature failure. 50.2 Please note that the steps are shown both for… Peripherals Embedded vs hosted images in email signatures Video by: Exclaimer To add imagery to an HTML email signature, you have two

Replace DC Controller PCA. 16 TONER LOW 1. HP LaserJet Error Codes and Service errors Back For additional help please Email our technical department Choose the error number from the menu below 02 11 12 12.x 13 13.x 14 You've made my day!! Replace Formatter PCA. 79 SERVICE (Document Error) 1.

Inspect Fiber-Optic Cable between Laser/Scanning Assembly and DC Controller. 3. Add memory or simplify print job. 21 ERROR/PRINT OVERRUN/PAGE TOO COMPLEX 1. Trying to print envelope in duplex mode (envelopes cannot be duplexed). However, I would take the replacement printer.

Multiple copies will print without mopying. It also loses tray size info after a few print jobs and has to be re-entered manually.The event log shows 41.03.00 GENERAL MISPRINT ERROR that seem to correspond to the display by drtch1 on Feb 7, 2012 at 9:17am Add comment Please sign in to comment 0 Moe, You are the man. Reset by pressing the continue key. 2.

Search the Community Entire ForumThis CategoryThis BoardUsers turn on suggested results Auto-suggest helps you quickly narrow down your search results by suggesting I accessed GUI using IE browse. What I think happens is that the laser hesitates momentarily (controlled by this board), but it is not long enough for the laser error (51 or 52) to be registered. When it prints, it prints a blank sheet of paper first and then prints the actual form/page....then it stops, hesitates and reboots, then prints again.

At full tilt, and while heating the fuser, the printer will consume about 1kW. It was the separation roller not clipping onto the torque clutch properly(as DMZCOMPUTE mentioned) that caused the fault. While the fuser is warming, the gears will turn so everything warms up evenly. Replace formatter PCA. 4000/4050/4100/5000/8000/8100 Only: 1.

Replace font cartridge. 2. Personality cartridge installed in font slot is incompatible with printer. 72 SERVICE 1. Regards. 0 LVL 1 Overall: Level 1 Printers and Scanners 1 Message Author Comment by:tcampbell_nc2009-09-16 The only driver I could find for this printer was the HP Universal Printing PCL The problem occurs only when printing from Tray 1 or Tray2.What do you think could be the problem?Percy by unknown on Jan 30, 2006 at 8:26am Add comment Please sign in

Check PS501 and PS106 (only on the Laserjet 4100) 13.6 Paper stopped jam at fuser. 13.10 Paper jam in Duplexer. You could try with the power off to remove and reseat. Replace Paper Input PCA. 5. DC Power Supply/Main motor driver malfunction.

I was going to replace the registration unit- output roller assy- and paper tray sense buttons. It could also be something with you network and not the card in the printer. Apart from the energy saving, having the printer stay at full power will also wear it out much faster - it would probably not last much more than 6 months, and If pages stick together, the paper detect sensors will detect a sheet of paper longer than what is expected in the product.

That paper is used, i think in one of the older copiers. I am at a loss, and have a group of legal secretaries on the war path. ran a 500 page with duplex print no problems. External fuser access door not closed. 4P/5P Only: 1.

i have to power off printer and power on, then it starts again at exact speed of printing. Hopefully the problem will evaporate. 41.X Error 41.X ERROR This usually means that "a temporary printing error occurred." For help press ? These technical pages do not constitute an offer for sale; just our knowledge at the time of writing. Copyright G & J Huskinson & MindMachine Associates Ltd 2013, 2015.

Check tabs on side of toner cartridge. That entire time, we hear the engine spinning, similar to the way it sounds with first powering up the printer. 0 LVL 37 Overall: Level 37 Printers and Scanners 37 No cleaning is necessary unless the printer has toner spillage or paper dust inside. I have found that in legal offices, the 200000 pages is overly optomistic.