frigidaire range error code f11 Selma Virginia

Address 204 W Main St, Covington, VA 24426
Phone (540) 962-8433
Website Link

frigidaire range error code f11 Selma, Virginia

I cleared the error and beeping stopped but when I re-started it gave the same error. Thank you for your question. Jack // Sep 8, 2015 at 3:20 pm Fridgidaire Mode FEFL78CBA, fault code 1, display controls function however oven not working. Ask a question Get up to 50 % off On Wall Ovens Related Questions Related Questions'>How can I get my Frigidaire oven unlocked? 1 answer Related Questions'>What does the fault code

Thank u again. Just in case you will decide to get new control panel, the part number for the control panel is 316538405 Good luck. No problems when powered back up. Expert: Tyler Z.

I washed the surface of the stove earlier today and when I turned the oven on it shot a flame out where the heat and condensation come out on top. The part number for the oven relay board 316443920 You can order the part by clicking on the part number. Thus if any of them failed, the whole heating element would need to be replaced. Wiedergabeliste Warteschlange __count__/__total__ Frigidare & Electrolux Stove / Range - Not heating or baking error code AbonnierenAbonniertAbo beenden33.77233 Tsd.

instead. I hope this is helpful information. -Matt Feb 25, 2015 | Frigidaire Kitchen Ranges 1 Answer My stove won't stop beeping and has a FC error code - can I stop Nächstes Video Top 6 Reasons Electric Oven Won’t Heat? — Electric Range Troubleshooting - Dauer: 3:31 42.835 Aufrufe 3:31 Frigidaire PLEF398DC Professional Series Electronic Oven Control Replacement - Dauer: 13:27 The controller does not see the motor rotating.  Press clear key.

So I guess the questions are,,,why did this happen and where do I go from here. what does that meanmy stove is beeping f11frigidaire range error code f11 and beepingmy oven displays f10 but can i still use the stovetopmy oven flashing f-11frigidaire range beeping error f11frigidaire Category:Appliance Share this conversation Expert: Tyler Z. Wenn du bei YouTube angemeldet bist, kannst du dieses Video zu einer Playlist hinzufügen.

There suppose to be one more letter. Remove the rear panel and locate two small power supply boards right next to the oven relay board. Tags: Oven error codes 232 responses so far ↓ Ron Hirtz // Nov 16, 2013 at 7:26 pm I have the F10 error code ohm reading at the plug into the My issue has not changed.

Learn more You're viewing YouTube in German. I have a Frigidaire model FFGF3047LSF. I hold the clear/off button down to unlock the door like book says for 3 seconds, then hold it longer because nothing happens, and then it says "F 11"I can't even lauraslaback Dec 27, 2008 I have the same problem!

Submitted: 6 years ago. If there is a such part, replace it. If the lock switch is defective, replace motor lock assembly. Wird geladen...

Thanks again. Where did you get the EOC you replaced recently? Click here to visit Merchant's home page. I checked the resistance on the probe's bare wires and it reads 1099 ohms.

Sorry for the delay. Please verify it. replied6 years ago. Billy // Mar 17, 2015 at 12:20 pm Hello Gene, I have a Frigidaire electric oven.

When did you install a new EOC? Thank you for helping an elderly veteran with this vexing problem. If fault returns when power is reconnected, continue the troubleshooting. The normal reading should be about 1100 Ohms at the room temperature.

The temp sensor is 1119 ohms never any fault codes shown on the display.any ideas on what the problem is . In this range there are no a separate keypad. Then when we started removing the relay board we found out it was fried (black soot). Same problem.

I was able to clear the lock and the oven gave an F1 code. What was wrong with the old one? I suggest resetting your stove by either unplugging it or disconnecting the power at your home's circuit breaker for 3-5 minutes. Click here:We can repair or replace your faulty Frigidaire CFEF358EB2 timer.CFEF358EB2 are also sometimes referred to using these Alternative Names/Model numbersElectrolux CFEF358EB2 Electric RangeCFEF358EB2 Schematic and Wiring DiagramsBackguard Parts diagramBody Parts

Could the water have shorted something out? Thank you. I have a frigidaire oven model FGF379WJC, and when I select any button on the oven control panel it displays, "OFF". Saves me a trip to the store to buy the wires.

Thanks, please let me know and I'll place an order. Replace the EOC. Gene // Dec 2, 2014 at 10:00 pm Hello Steve, Sorry to hear you have more problems with your range. Here is my previous reply: "Hello Valerie, Thank you for your question.

Well, it was almost a year to the date. I verified this was the case by removing the upper rear panel of the stove and disconnecting the keypad connector from the upper left of the lockout board. When we unplugged both of the P1 connectors and restored the power to the range the touchscreen was blank (no power), so I couldn't turn the oven on to see if If the igniter glows but the gas doesn't flow, possible the igniter itself is to weak to open the gas safety valve.