f4 error code whirlpool Fort Lee Virginia

My business is repairing PC's. Also helping the end user understand the problem, and explain the solution. If your PC is running slowly, I would resolve that issue, as well as virus removals, Hardware and Software installation, Data Back-up, Upgrades, and Reimages (If need be).

Address 5212 S Jessup Rd, Chesterfield, VA 23832
Phone (804) 714-0344
Website Link
Hours

f4 error code whirlpool Fort Lee, Virginia

Check wire harness connections between drive motor and Motor Control Unit (MCU), and between MCU and the Central Control Unit (CCU). Exactly the same error will be displayed if a door wire breaks from the control pcb in the fascia panel to the NTC. Ste. 500, Encino, CA 91436 1-877-477-7278 Tennessee 240 Edwards St. If error continues, disconnect power and replace control.

Check CCU is also operational by performing a diagnostic test or any cycle. Replace control board (clock). The machine control board may have a bad relay and may need to be replaced. Honolulu, HI About Us DIY Blog Our Story Core Values Locations Rave Reviews Affiliates Program Job Listings My Account Sign In My Account Order History Shopping Cart Our Policies Terms of

The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd. Check wire harness connections to pressure switch, drain pump, and Central Control Unit (CCU). Try unplugging the Unit for two minutes to see if that fixes the error. • Check CCU. The twist is, if the NTC is fluctuating in its reading it also can indicate F3 and not F1, because the NTC is the measuring device for the increase in temperature.

Open the lid or press STOP/CANCEL to clear the display. Disconnect power and unplug unit to check door switch/lock unit. Press PAUSE/CANCEL twice to clear the display. The electronic control (module pcb) does a self check of the components, during a drain cycle the programme allows a time parameter for the appliance to empty away the water.

Select a Timed Dry heated cycle and restart the dryer. F9 error fault code This is filling with too much water. Fault Codes Fault Codes Admiral Bosch Dacor Estate Frigidaire GE Gibson Hotpoint Jenn Air Kelvinator Kitchen Aid Magic Chef Maytag Roper Sears / Kenmore Tappan Thermador Whirlpool We are Safe, Secure, F3 is Lid Switch Failure and I could not find a F4 in the book.Quotewhere I can buy a manual that will tell me?Here is the manual.http://www.appliancejunk.com/manuals/catalyst.pdfPage 27 is were I

More Fun Back To Fault Codes Admiral Fault Codes Whirlpool Appliance Fault Codes Roper Fault Codes Gibson Appliance Fault Codes Hotpoint Appliance Fault Codes Kelvinator Appliance Fault Codes KitchenAid Appliance Fault This is continually tested to ensure proper lid switch operation. Press STOP/CANCEL to clear the display. The lid switch must be opened at least once before restarting the cycle, if this condition occurs.

Started by AJ Replies: 3Views: 18952 November 15, 2009, 09:34:58 AM by AJ Whirlpool Duet Washer F5 Error Code Started by TechnicianBrian Replies: 2Views: 16449 October 05, 2008, 08:39:47 PM by The flow meter impulse wheel (situated in the water tank) is not turning correctly, too fast or too slow therefore the electronic impulses received by the module/pcb are not correct, also Re-apply power. If code re-appears, replace control board (also called ERC or clock).

A failure of theWI (water indicator) which is the pressure switch or Turbidity sensor, to switch, this can be because of muck and dirt blockage to the pressure device which means Unplug the power cord from the outlet. 2. The pressure switch is a chageover switch, The sensing grid of the pressure switch is exposed to the dishwasher wash water and can over a period of time get clogged with What that means is that the flow meter is not recording water entering the dishwasher, this can be a water tap turned off (suprisingly more common than you'd think, after new

Or maybe where I can buy a manual that will tell me? Allow at least a minute after power has been restored and if error code reappears, replace control board (clock). F1-E6 - Latch Signal Mismatch Error - Disconnect power for at least 30 seconds and then reconnect. Yes No Thanks!

F2 - Oven Temperature Is Too High - Check for welded contacts on bake and broil relays. Thanks, Jack Jack H for Model Number GSX9885JQ0 ANSWER Jack, Here's the information you need : DISPLAY EXPLANATION AND RECOMMENDED PROCEDURE F3 LID SWITCH FAILURE “F3” flashes and cycle signal beeps Potential Causes • If too much detergent was used, run the unit through a Rinse/ Spin cycle then a Normal cycle without adding any detergent. Press PAUSE/CANCEL twice to clear the display.

If a failure occurs during high-speed spin the door will be unlocked after 3 minutes. If door latched: Disconnect power from unit. It can also indicate a bad pump, an extra heavy load, excessive detergent, or excessive suds. Virginia Beach, VA "Your service people are so friendly and helpful.

Disconnect power for at least 30 seconds. 2. Close the lid and press 'Start' to continue. Reconnect the unit and power to verify the pressure switch is operational, as well as the flow meter (blow air through the flow meter and measure resistance). Also check for any causes of high resistance in the oven temperature sensor circuit.

SL - Suds Lock - This error will occur if the unit detects suds but is unable to clean them out. Press STOP/CANCEL to clear the display. ^ top LS Lid switch error The control should flash this error code if it cannot detect the lid switch opening and closing properly. NOTE: Beeper will sound continuously while error code is flashing. Check sensor, sensor harness, and the sensor harness connection at sensor and oven control.

Look for pinched wire. Wires to the recirculate pressure switch disconnected or not connected correctly. – Failed recirculate pressure switch. If error code returns after 60 seconds, replace keypad (also called touch pad or membrane switch). F5 - E0 Door switches do not agree (condition exists when door switch is closed indicating an open door, and latch switch is closed indicating a locked door) 1.

Ld - Long Drain - This error code will appear if unit takes longer than 5 minutes to pump out water to the point where the pressure switch resets. Check for stuck lock switch. Select the 'cancel' function and wait 60 seconds. Press 'Stop/Cancel' to clear display.

Unplug the unit to service. Check the MCU by looking for operations of the drive motor, and check drive motor for powered rotations. If there is an error reading this data it will cause this error. All other trademarks are owned by their respective companies.MSRP is Manufacturer's Suggested Retail Price and may not necessarily be the price at which the product is sold in the consumer's area.