f10 error frigidaire Flint Hill Virginia

Address 4221 Frost St, Marshall, VA 20115
Phone (540) 364-5288
Website Link

f10 error frigidaire Flint Hill, Virginia

The overlay part number is 316419103 If it happened while the oven was in cooking mode, start the troubleshooting from testing the temperature probe for continuity as described in the article I pressed the cancel button, but the error comes back. Gene. Gene.

Per your description the reading at the EOC is incorrect while the sensor itself checks OK. Severe overheating may require the entire oven to be replaced should damage be extensive. 2. (F11, 12 & 13) Disconnect power, wait 30 seconds and reapply power.3. (F11, 12 & 13) Gene // Mar 29, 2015 at 6:41 pm Hello MML, Sorry for the delay. It is giving F11 error.

It would need to be replaced. Do you have any other questions? This particular control panel was designed for this model only. Enjoyed reading your help to other people.

Remove the back panel. This information is based on the common Frigidaire range models. The cause of the problem can be a faulty potentiometer or a faulty User Interface Board. Melted the teflon off a baking pan.

If oven is overheating, disconnect power. Valerie // Apr 24, 2015 at 7:00 am Hi Gene, I am having problems again and before I order on my diagnosis, I wanted your confirmation. Thank you. To test operation of the potentiometer m Später erinnern Jetzt lesen Datenschutzhinweis für YouTube, ein Google-Unternehmen Navigation überspringen DEHochladenAnmeldenSuchen Wird geladen...

The black potentiometer should have a resistance of 10KΩ. Kevin Foster // Jun 6, 2014 at 6:47 am Good day, Gene I have a Frigidaire Electric Range Model #GLEF379DBK The other night my range just started beeping all of a Specifically the orange wire on the connector adjacent to the only non square or rectangular black component on the board. MML // Mar 31, 2015 at 4:09 pm Hi Gene, Thanks so much for your reply.

Can you please tell me, does this sound like a bad control board? Hinzufügen Möchtest du dieses Video später noch einmal ansehen? Gene // Mar 15, 2015 at 6:56 pm Hello Rachel, Thank you for your question. If you see F10 on your range, it means that your electronic control board has detected a runaway temperature.

If the resistance is normal through the wires that plug into the control board, then it is likely that you will need to replace the control board. IMPORTANT DISCLAIMER: The Author of this web site assumes no responsibility for inconveniences or damages resulting from use of the information he supplies. Gene. Mike Mike and other Appliance Specialists are ready to help you Ask your own question now Customer: replied6 years ago.

F10 indicates a bad temperature sensor. Any ideas. If you order them from AppliancePartsPros.com, you can return unneeded part later with full refund. The part number for the EOC is 316418735 To order a part just click on the part number.

If fault returns after reconnecting power, replace the EOC. F95 Door motor mechanism failure. sergio // Mar 1, 2015 at 6:28 pm I keep getting a code f10 i replaced the eco on my oven.part 316455410 about three months.the problem was fix .now I have Browse by Appliance Dishwasher Dryer Freezer Garbage Disposer Microwave Range Hood Range / Oven Refrigerator Trash Compactor Washer Browse by Brand Amana Parts Bosch Parts Dacor Parts Frigidaire Parts Hotpoint

The part number for the potentiometer is 316239605 The part number for the UIB is 316426400 Good luck. Check RTD sensor probe and replace if necessary. You can order it at www.repairclinic.com. thanks josh Gene // Apr 10, 2014 at 5:03 pm Hello Josh.

Keep me posted. With this info. note: disconnect the power cord from the power source before servicing your range. Gene // Apr 1, 2015 at 8:16 pm Hello MML, Sad news about that ribbon cable.