general error. recvfrom failed 10054 West Dummerston Vermont

Address 170 Grassy Brook Rd, Brookline, VT 05345
Phone (802) 365-4723
Website Link http://2wiredguys.com
Hours

general error. recvfrom failed 10054 West Dummerston, Vermont

not TCP/IPServerName; InstanceName; SQLExpressIsClustered; No; Version; 11.0.2100.60;; Cause: The driver communicates using the TCP/IP network protocol which needs to be enabled for the database. Terms of Use. Instance "dg4msql", status UNKNOWN, has 1 handler(s) for this service...The command completed successfullyLSNRCTL>Thank you ! You cannot post IFCode.

Your comment indicates that you regard the Restore points as a handy way of saving a chart display. Resolution: Follow the steps given in the below article https://technet.microsoft.com/en-us/library/ms191454%28v=sql.105%29.aspx Then post the above step I got the below error Connection test failed: Error in testing the connection: Connect faild.Error type: A: The two colours are provided to tell you whether a particular aircraft in Plane Plotter was last received by you or by someone else. There is nothing you need to enable for that to happen.

Where do I find ppregfix? the Web site airframes.org was listed as Always Block. All Rights Reserved. Like Show 0 Likes(0) Actions 2.

You cannot post new polls. It would be good if you could find out what is wrong so that you can return to contributing raw data for everyone's benefit. "On opening the ACARS wave device...device recv failed: 10054 Can some one help me to rectify this error? Right click the file you have saved, and select Properties.

Tns error struct: ns main err code: 12541 TNS-12541: TNS:no listener ns secondary err code: 12560 nt main err code: 511 TNS-00511: No listener nt secondary err code: 61 nt OS When I run the two seperately, for example: my console application would prompt whether you want to run server or client. You cannot edit your own posts. To be technical I am a seasoned MicroStrategy Certified Developer and a Netezza Silver Certified Professional.

We're currently troubleshooting, but our best guess right now is network error. Apparently this was a known bug sometime back that was fixed with sp4 (I think!)... **ASCII stupid question, get a stupid ANSI !!!** Post #184473 happycat59happycat59 Posted Monday, May 23, 2005 Register now! The requirement is for +/- 2 seconds.

Close and restart Plane Plotter. Almost all questions of the form "Why did my xxxxx setting suddenly change when I didn't do anything?" are answered with "You asked it to change when you pressed A,B,C or FTD driver FTD2XX.DLL (version 2.08.24) Make sure you have correct settings in PlanePlotter: Options > I/O settings - SBS 1/3 direct TCP Options > Mode S receiver > Kinetic SBS Every time I start PP it tells me it cannot find a .clb file By way of an experiment, I tried to import a chart into PP the other day.

Left Click on X at the top right of the dialogue box to close it. Why do local aircraft move but not shared ones? From now on, when you click to run a file with a .VBS extension, it will be executed rather than opened in your browser or Notepad editor. I managed to collect all datagram packets send by the sender programme through a loop.

This normally results if the peer application on the remote host is suddenly stopped, the host is rebooted, the host or remote network interface is disabled, or the remote host uses How I can make sure it does not exit till I receive all the packets from that port. You may have accidentally pressed F9 which toggles prediction, or you may have not checked the Predict positions over check-box in the chart setup dialogue which is invoked from the spanner Characters Remaining: 255 Copyright © 2016, Progress Software Corporation and/or its subsidiaries or affiliates.

All Rights Reserved. Unless you are intentionally moving location, it is important that your location remains fixed and accurate. I also activated another udp sender application to inject udp packets into 127.0.0.1 10. Privacy Policy.

QNH doesn't work but normal sharing does Please note that QNH uses FTP to retrieve the data, rather than HTTP which is used for normal sharing. They may be TIS-B codes, used in the USA. If select() returned 1, you can read the socket. Here is the fun part: Mode-S gives the ICAO hex code, no rego, and a version of the flight number.

Error: undeclared identifier My function declared as follows: DWORD CALLBACK xxx() I called this function within the thread from another function using the following syntax function(&xxx,etc); thread is created as follows. cb transfer status: 4, canceling .... You cannot post HTML code. So if sharing works, and QNH does not, check the Plane Plotter program and your PC is allowed to do FTP transfers by your firewall software.

Access is denied" A: Be sure to close down all instances of Plane Plotter before you try and install a new version.