fax modem error Lake Elmore Vermont

Address 1463 Ripley Rd, Waterbury Center, VT 05677
Phone (802) 244-5088
Website Link http://www.maplepro.com
Hours

fax modem error Lake Elmore, Vermont

fax troubleshooting checklistpage 121................................................................................................................................................................ This is usually because other applications are running. Wiring and Hardware Factors Test that phone cable is working properly: Sometimes an old or damaged phone cable is the culprit, causing line noise. Yes, DR support is available in the desktop version of snappy fax and implemented in build 5.13.1.1 and higher and snappy fax server build 5.40.1.1 or higher.

The printer picks up on a greater number of rings than the answering machine. Unsupported Compression The fax modem of the receiving fax machine does not support data compression. Try using the Modem Reset Strings on the Modem page of the Preferences (Program Settings) dialog box. Phone Line Busy Your telephone line or the telephone line of the receiving fax machine is busy.

The HDLC carrier did not stop in a timely manner The fax service initiated a fax transmission with the receiver, but there was a synchronization (timing) error that could not be This may be due to a call clarity issue. Digital line detected The printer is connected to a digital line. If your transfer rate is set above 9600, try changing it to 9600, 7200, or 4800 and see if this helps with receiving faxes.

This is accessed via the Preferences screen as Item #22b Reset Modem Between Calls. 2. If you do not hear a dial tone, then contact your line provider. If you were a previous WinFax user then the WinFax service is the likely culprit. To connect the printer to a digital line, you must use a digital line converter or a filter.For more information, see the "Setting up the printer to fax" section.Failed to ConnectPhone

If you enable distinctive ring then you may lose your caller id information. Back to Top Issue 4: Cannot Run the Fax Software The printer must be connected to a telephone, DSL, VoIP, or cable service before you can configure the fax settings in This happens especially if the printer is sharing the line with other devices (telephone, answering machine).Set the printer to redial.Increase the time between the redial attempts.Place a test call to the If you have other devices connected to the wall jack by means of a splitter then the othere devices may degrading the ring signal to a level that the modem cannot

Draft mode will allow you to create the fax from multiple files, print operations, scanning, etc. Snappy fax tells me my modem is in use, what does this mean exactly? This option enables the printer to transmit the bad blocks of data again and correct the errors. Will my modem and snappy fax work with Vonage or MagicJack?

The fax modem of the printer may be busy, or the fax modem may have encountered problems during transmission. Enable Auto Fax Conversion. You should only check this option after you have diagnosed why the modem isn't detecting the dial tone as this condition usually indicates a problem with your modem connection/setup. Make sure the phone line splitter is not interfering: If you use a phone line splitter, which plugs into a single phone outlet and turns it into two or more outlets,

cannot print and there is a firewall on the computerpage 131................................................................................................................................................................ This is accessed via the Preferences screen as Item #3 Modem Reset. Board index The team • Delete all board cookies • All times are UTC - 8 hours Powered by phpBB Blog Company Careers News & Media Demo Awards Contact Legal Site Some fax machines also block faxes without sender information.Fax Mode UnsupportedThe receiving fax machine does not support color fax or the scan resolution of the document that you are sending.Enable Auto

If you are using a PBX system, then make sure that the printer is connected to an analog port on the PBX. This is accessed via the Preferences screen as Item #16 Transfer Rate. Try turning these off temporarily and see if that helps. Don't show me this message again.

The only difference is that the SG3 editions support fax class 2.1 which allows sending faxes at speeds greater than 14400 bps when communicating with other Super G3 fax devices. The fax modem of the receiving fax machine does not support data compression. To further complicate this situation, Windows provides no way for snappy fax itself to discover which process it is. Essential FAX Software Home Overview Screenshots Download Purchase Support FAQ Technical Home > Technical Articles > General Troubleshooting for Fax Receiving In most cases, reliable fax receiving should occur after doing

The error on the receiving end could be due to several factors.Resend the fax. Vincent und die Grenadinen Südafrika Surinam Swasiland Tadschikistan Taiwan Tansania Thailand Togo Trinidad und Tobago Tschad Tschechien Tunesien Türkei Turkmenistan Turks- und Caicosinseln Uganda Ukraine Ungarn Uruguay USA Usbekistan Vanuatu Venezuela Unexpected message received The fax service received a message that it did not expect given the current context. A common disable code is *70, (note the comma, it is necessary).

The vast majority of modems on the market are not class 2.1 modems. Depending on the remote machine's behaviour, it may have still printed the sent page and any preceding pages. The modem's 'Line' jack should be connected to the wall jack. The fax modem encountered critical errors.

The telephone cable is connected to the wrong port on the back of the printer. This could be due to there being no fax machine on the receiving end, or a lack of call clarity. Far end cannot receive at the resolution of the image The remote fax machine does not support receiving faxes sent at the resolution that our service sends at. In some countries, you cannot send a fax without registering your fax name and fax number.

The speed of the modem of the receiving fax machine must match or be greater than the speed at which you are sending your fax. If the printer is connected to a VoIP adapter or cable modem, then make sure that the printer is plugged into the first phone port. If you hear a dial tone but still have problems sending and receiving faxes, then see the other topics listed below. Note: if you have a Rosewill USB modem...

When a fax has too many errors, the fax may be rejected by the receiving fax machine.From the printer control panel, navigate to:> Setup> > Fax Setup> > Dialing and Sending> Hint: If you press Ctrl-C on the keyboard when the error message box has focus, it will copy the contents of the message box to the windows clipboard, you can then If the receiving machine does not support color fax, then this option automatically converts the outgoing fax to black and white and also automatically reduces it to a resolution the receiving If the printer runs out of ink or runs out of paper while receiving the fax, then the printer saves the fax so you can print it later.

You may risk damaging your registry which leads to all sorts of bad things happening. Make sure the cables are securely plugged in. Make sure you plug the telephone into the same port.