frigidaire professional series oven error code f13 Sigurd Utah

Address 70 N Main St, Central Valley, UT 84754
Phone (435) 896-4451
Website Link

frigidaire professional series oven error code f13 Sigurd, Utah

Plug the oven back into the electrical outlet. BUT oven not heating up. Your expert will also help answer your question. thank you….tom Gene // Sep 7, 2015 at 9:32 pm Hi Tom, Thank you for your question.

It is just run away heat. Frigidaire incorporated keypad into the electronic control board for most of the models and used just a faceplate or overlay which is adhered to electronic control board. The part number for the relay board is 316443918 You can order the part by clicking on the part number. The overlay part number is 316419103 If it happened while the oven was in cooking mode, start the troubleshooting from testing the temperature probe for continuity as described in the article

Black ... Could you please explain what this is. Is there a way to silence the alarm so we can still use the range? Gene // Dec 24, 2014 at 1:10 pm Hello Craig, It is not difficult to do it but, for more accurate advice I need the complete model number of the oven.

Keep me posted. The porcelain wire nuts part number is AP5641944 Good luck. Good luck and keep me posted. My wife is suspicious of the temperature, however.

The part number for the EOC is 316557205 The part number for the overlay is 316419303 Good luck and keep us posted. I did this and it didn't work. I was not aware of a door lock (because I don't see anything to slide) other than the "lock" symbol on the control panel that I've never used… Can you tell? PDF Manual 50385155-434c-467c-aabc-0a989e4fbb16.p...

When I test those two part on it I get the same results. If you ordered the EOC and the temperature sensor from AppliancePartsPros. George // Dec 1, 2014 at 4:55 am Hi Gene, I posted this on 11/24/14 but somehow it was deleted. Gene.

Broiler works fine. Check the temperature sensor resistance as described previously. I guess you get what you pay for ... All Electronic Oven Controls (EOC) have ability for self diagnosis.

To start viewing messages, select the forum that you want to visit from the selection below. Possible there is something wrong with the oven door hinges. Gene. Also the model number you sent is incomplete.

Ed // Apr 27, 2015 at 11:01 am Hi Gene, Per your suggestion, I cut the 2 violet wires (the 2 running between the EOC and the RTD temperature sensor) and It's self-adhesive and if it can not be safely removed from the old EOC and properly attached to new part, you may want to order the overlay as well. Unplug the oven from its electrical outlet and slide it away from the wall. When the repairman come sout, the oven may be functioning properly, so it is hard to verify this intermittent problem.

The part number for the temperature probe is 316490000 If the reading is normal, the EOC has failed and would need to be replaced. I will show you how to diagnose and fix them depending on the fault code. Ask a question Get up to 45 % off On Ranges Related Questions Related Questions'>What does F31 error code indicate on a Frigidaire gas range? 1 answer Related Questions'>What does F1&F2 Other People Are Reading Frigidaire Oven Error Codes How to Replace the EOC on a Frigidaire Plug each of the wiring harnesses into the EOC.

Order Appliance Parts with 365-Day Hassle Free Return Policy - #3 (permalink) 03-20-2008, 03:01 PM JORGEMEDE Junior Member Join Date: Mar 2008 Posts: 1 Alive again...!!! The cause of this problem most likely is a faulty EOC. Now it's happening again! what does this mean ?

The burners work fine, oven cannot be used. Gene // Jan 12, 2015 at 11:11 pm Hello Ehsan, F11 error code means a shorted key in the keypad. All such igniters are interchangeable. The part number for the EOC is 316562003 The part is on back order.

Why wouldn't the whole burner quit? See Details More Products Frigidaire FFGF3015LB 4.2 cu. Jeff // Jul 17, 2015 at 2:59 pm Hi i'm having a problem with my Frigidaire oven professional series model number PLES389ECH I've followed your assessment steps with the following findings The wires look OK (no visible external wear) from the plastic connector in the back of the EOC module down to the metal bracket holding the RTD temperature sensor into the

model plgf389cce Frigidaire professional series Gene // May 17, 2015 at 6:34 pm Hello Greg. F8, F9 or F90 - Lock motor switches improperly positioned. Especially since the EOC had failed once before on warranty (it completely burned out and wouldn't work at all) and the repair tech told me that self clean was likely to Gene.

Michele Gene // May 10, 2015 at 9:56 pm Hello Michele, Sorry for the delay. Any ideas. John // Apr 8, 2015 at 7:28 am Here is the actual label on my stove. [IMG][/IMG] Gene // Apr 8, 2015 at 2:04 pm Hello John, I did not question It may take two business days.

Usually an hour or so after it has been shut off. Gene. The potentiometer is the control for surface element. Ed Gene // May 6, 2015 at 9:35 pm Hi Ed, Put everything back together and give it a try.

Gene // Apr 1, 2015 at 8:35 pm Hello Steve, Thank you for your question.