frigidaire oven error codes f10 Sevier Utah

Web Design Services We offer customized professional, prompt & inexpensive Web site design services to meet your needs. Emerging Technologies As convergence combines old & new ideas -- in Multimedia, Mobile & Internet Phone Solutions, Smart Homes, and Entertainment -- we make sense of it all. Intermountain Computer Services 70 North Main Street Richfield, Utah 84701 4358964451

Address 70 N Main St, Richfield, UT 84701
Phone (435) 896-4451
Website Link
Hours

frigidaire oven error codes f10 Sevier, Utah

In situation you described most likely the EOC has failed and would need to be replaced. My question is this, would that be the main culprit? if wiring is good, replace the EOC. Where did you get the EOC you replaced recently?

By the wiring diagram for your range, both oven heating elements getting power from the EOC. Thank you for your question. I dont know model number but do think the stove could have shorted out and it ave a f10 code Gene // Dec 19, 2014 at 8:29 pm Hello Darlene, The Gene // Jan 4, 2015 at 1:07 pm Hello Eric, If the problem just melted wire harness connector and the temperature probe tests out OK then the easiest solution is to

Thanks Reply With Quote May 26th, 2011,11:33 AM #6 Jake View Profile View Forum Posts Visit Homepage Appliance Tech - Admin Join Date Aug 2004 Location McMullen Valley, Arizona Posts 79,575 Gene. Jay // Sep 2, 2015 at 11:53 am Gene, I have a Frigidaire FEF368gba with F10 code coming up. Unplug your range first before opening it up and checking it.

Neil Gene // Apr 5, 2015 at 9:46 pm Hello Neil, Thank you for your question. Be sure to check out the other videos, here on the YouTube channel, and don't forget to subscribe. Jeff // Jul 17, 2015 at 2:59 pm Hi i'm having a problem with my Frigidaire oven professional series model number PLES389ECH I've followed your assessment steps with the following findings Shorted Probe connection. 1. (F30 or F31) Check resistance at room temperature & compare to **RTD Sensor resistance chart.

Gene. Severe overheating may require the entire oven to be replaced should damage be extensive. Jim // Dec 8, 2014 at 1:00 pm Hi Gene. If 1100 ohms is present replace the ERC.

she gets error code 11. There are probably over 50 different error codes but in this article we will review only the most common ones. Any advice would be greatly appreciated. The resistance reading on the sensor should be close to 1100 ohms at a room temperature of 75 degrees.

Happy holidays to you and your loved one as well! now F10 error, checked probe and it reads over 1100 ohms. Ken // Dec 28, 2014 at 1:36 pm Hello Gene, Thank you for the info.. What should I focus on next?

You may want to replace it as well. Gene. Thanks Larry Gene // May 20, 2015 at 3:07 pm Hello Larry. Maybe worthy of note - I did not piece together everything (burners not screwed back in; metal piece covering the wires in back not screwed in).

Why wouldn't the whole burner quit? Thanks. If the door lock motor never stops rotating, or if the F95 error comes back again, verify wiring of the motor. Ed Gene // Apr 23, 2015 at 9:29 pm Hello Ed, Thank you for your question.

I have an Electrolux model#EW30DF65GSB. If the reading is incorrect, remove the sensor from the oven and check its resistance at the sensor. John // Apr 8, 2015 at 7:28 am Here is the actual label on my stove. [IMG]http://i62.tinypic.com/4t7oyg.jpg[/IMG] Gene // Apr 8, 2015 at 2:04 pm Hello John, I did not question If the range is actually overheating, then you could have a stuck relay on the control board, which means that you'll have to replace that control board to fix the problem.

CT Sat 7:00 a.m. - 9:00 p.m. You may want to start the troubleshooting from checking the temperature probe for continuity, using a multimeter. The part number for the EOC is 316562003 The part is on back order. Check RTD resistance at room temperature ( compare to probe resistance chart ).

Thread Tools Show Printable Version Search Thread Advanced Search Display Linear Mode Switch to Hybrid Mode Switch to Threaded Mode October 5th, 2010,08:49 PM #1 Roccobon View Profile View Forum Max // Sep 3, 2015 at 6:35 pm Hi Gene! Disconnect power, wait 10 seconds and reapply power. Mike Gene // Jun 6, 2015 at 10:30 pm Hello Mike, Thank you for your question.

Logged Take a Kid fishing. Possible the EOC has failed. Gene. We ordered both the parts, tried the EOC first, with no fix.

The display should be blank.