frigidaire range error code f10 Simonton Texas

Address Po Box 74, Wallis, TX 77485
Phone (979) 993-3400
Website Link http://www.larktech.net
Hours

frigidaire range error code f10 Simonton, Texas

by LYLE W. The part number for the temperature probe is 316490000 If the reading is normal, the EOC has failed and would need to be replaced. Carefully pull it out and, using an Ohmmeter, check the resistance between the sensor wires. If the door lock motor never stops rotating, or if the F95 error comes back again, verify wiring of the motor.

Dirk // Apr 25, 2015 at 4:10 pm Hi Gene, I have a Frigidaire electric range model FEF366DSA and the broil and oven elements are not working but the surface elements note: disconnect the power cord from the power source before servicing your range. It's possible that your range is not heating to the temperature that you set it to, or the control board may be reading the temperature incorrectly. Gene // Dec 24, 2014 at 1:10 pm Hello Craig, It is not difficult to do it but, for more accurate advice I need the complete model number of the oven.

Starts beeping then stops and starts again after a while. To test operation of the potentiometer m Später erinnern Jetzt lesen Datenschutzhinweis für YouTube, ein Google-Unternehmen Navigation überspringen DEHochladenAnmeldenSuchen Wird geladen... Gene. If I should replace the range, is this a common and eventual issue with all electric ranges and the electronics on them?

the oven control can is access and replaced from behind the range. Most likely there is only one problem caused by the faulty EOC, but there is a very small chance for the latch motor to fail as well. CT About Us Sears Commercial Parts Contact Us All Brands Parts Store Locations Top Parts All Categories Affiliate Program Appliance Parts Refrigerator Water Filters Lawn Mower Parts Snow Blower Parts Join Press UPPER OVEN or LOWER OVEN to select oven. 2.

Yes, the temperature sensor tests OK. The motor does not stop rotating.  Press stop key. Gene. Gene // Apr 1, 2015 at 8:16 pm Hello MML, Sad news about that ribbon cable.

Earned 106,588 community points in Click'>Appliances April 2nd, 2009 Comment Give your feedback by voting on answers 0 votes Didn't find what you are looking for? It's possible that you need to replace the electronic control board or the temperature sensor. In order to provide most accurate advise I need the complete model number of the oven. Keep me posted.

You can find it on the range frame behind the bottom drawer. Wird verarbeitet... I am lost as to how to proceed next as the touchpad was included with the new EOC? Press CANCEL to reject the change if necessary." If the temperature is out of range for more than 35°F, it can not be adjusted.

Gene. Rachel // Mar 14, 2015 at 8:14 am Hello, My range is showing F10 error code since this morning. My issue has not changed. After several power-cycles with the same error, I came to your page.

Mike Gene // Jun 6, 2015 at 10:30 pm Hello Mike, Thank you for your question. Gene. Gene. Sounds like the EOC is the culprit.

Powered by vBulletin Version 4.2.3 Copyright © 2016 vBulletin Solutions, Inc. If the readings are the same and you continue to get the F10 error code when trying to cook, then the electronic control board will need to be replaced. Model retention may be affected by your browser settings. how do i fix this i havn't even had the stove for a year.

Thank you for your question. Start the troubleshooting from verifying the resistance value of the potentiometer. Gene. Let's check the oven temperature sensor first.

Len // Dec 23, 2014 at 11:03 pm Hi Gene: I have a Frigidaire Gallery -Self Cleaning Convection Oven (electric) model#DFEF385JHS2. Eric Johnson // Jan 4, 2015 at 1:10 pm You can disregard my question, thanks to your troubleshooting steps on this page, I managed to isolate the problem and repair my Wird geladen... Page 1 of 2 12 Last Jump to page: Results 1 to 10 of 14 Thread: [FIXED] error f10, shut breaker off now oven normal?

If all situations above do not solve problem, replace EOC. Crystal // Mar 17, 2015 at 7:45 pm Hello, I have a Frigidaire Model#FGF337ABJ. It is producing the F10 error code at room temperature/day time mode. In situation you described most likely the EOC has failed and would need to be replaced.

code goes away immediately upon opening the oven door. It suppose to be about 1100 Ohms. Jake Appliance Repair School 1987-1988 Star Appliance Tech. 2 yrs. 1988-1990 Wards Appliance Tech. 11 yrs. 1990-2001 Sears Appliance Tech. 4 yrs. 2001-Oct. 2005 Jake's Appliance Repair Nov. 2005-present Look-Up & I shut the breaker, waited about 30 mins then flipped the breaker back on and the error was gone.

Keep me posted. the oven temperature sensor can be removed and tested for resistance and compared to the rtd scale in the image below. Good luck. It wasn't until after I researched it that I found this envelope, left there by the previous owner.) In my case, when I turned the oven on to "Bake", the broiler

Let me know the result. With this info. Autoplay Wenn Autoplay aktiviert ist, wird die Wiedergabe automatisch mit einem der aktuellen Videovorschläge fortgesetzt. The wiring harness resistance indicates no connectivity (the purple wires coming from the EOC).

Mike Ask Your Own Appliance Question Customer: replied6 years ago. AppliancePartsPros.com is the registered trademark of AppliancePartsPros.com, Inc. Check RTD resistance at room temperature ( compare to probe resistance chart ). On most Frigidaire ranges, the F10 indicates that the control detects a runaway temperature in the oven.

The content on this web site is for informational purposes only and is not intended to replace an on-site diagnosis from a qualified appliance service technician. Sad news. The instructions on how to adjust the upper or lower oven temperature usually are in the Owner Guide.