frigidaire error f31 Scurry Texas

Address Forney, TX 75126
Phone (972) 467-8604
Website Link
Hours

frigidaire error f31 Scurry, Texas

John // Apr 8, 2015 at 7:28 am Here is the actual label on my stove. [IMG]http://i62.tinypic.com/4t7oyg.jpg[/IMG] Gene // Apr 8, 2015 at 2:04 pm Hello John, I did not question Answered by AppliancePartsPros.com|Monday, June 29, 2015 We are Safe, Secure, Dependable and Trusted Newsletter Signup Receive discounts, usage tips, and recall notices. NOTE: You should only access and check internal range components if you are completely confident in your technical ability to safely perform the process. Should I replace the EOC?

Gene. Master 6,784 Answers Re: Oven shows error F31 when trying to bake F31 - Shorted Temperature Probe connectionCheck the sensor probe connections for damage. Last night I tried to use the oven and it started flashing a F30 error. I don't think anything else but EOC is the main culprit.

Thank you, Gene. Add your answer Sign in to answer a question 1 Answer from this member: The F31 error code indicates a shorted oven temperature sensor probe or a shorted sensor circuit. Home Where is my Model Number? Remove the power from the oven and pull the oven out of the cabinet.

My issue has not changed. I have included a link below on how to test the sensor, and a link to the oven sensor for your model range. From what you have described your Frigidaire range is displaying an "F31" error code. The part number for the EOC is 316455410 Good luck.

Eric Johnson // Jan 4, 2015 at 1:10 pm You can disregard my question, thanks to your troubleshooting steps on this page, I managed to isolate the problem and repair my Possible there is something wrong with the oven door hinges. The part number for the oven relay board 316443920 You can order the part by clicking on the part number. The black potentiometer should have a resistance of 10KΩ.

In order to provide most accurate advice I need the complete model number of the oven and the part number of the EOC you installed. This error code indicates a failed potentiometer for LF burner, a user interface board or the harness between the mother board and the user interface boards. If the reading is incorrect check the sensor wire harness and repeat the continuity test at the RTD bottom plug. Thanks Larry Gene // May 20, 2015 at 3:07 pm Hello Larry.

After several power-cycles with the same error, I came to your page. Frigidaire used the name RTD sensor or RTD probe, where RTD means "Resistance Temperature Detector" instead of oven temperature sensor. The content in this area cannot be displayed because your browser has JavaScript disabled (or does not support it, not common). This seems to have happened randomly after years of fine operation.

Yes, there is the power relay board which is located behind the oven rear panel. If the fault returns, replace the keyboard ( membrane ). The EOC part number 316455400 Thank you for your question. is online now I have a Frigidaire gallery range that gives a code F31 when This answer was rated: ★ ★ ★ ★ ★ I have a Frigidaire gallery range

Add Thread to del.icio.us Bookmark in Technorati Tweet this thread 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 Getting your parts... 24/7 From my understanding your Frigidaire range, LFGF3014LBC, is displaying an error code of "F31". Gene. Gene.

Can you tell me what could be causing this error code and what parts I'll need to replace? Check wiring of lock motor, lock switch and door switch circuits. I'll be helping you with your problem today.F31 means that your oven thinks the oven sensor is shorted. How do I find out if can be fixed,or repaired?

If the reading is incorrect and the wires and plugs between the sensor and the EOC are good, replace the temperature sensor (RTD probe). The normal reading should be about 1100 Ohms at room temperature. Frank // Feb 27, 2015 at 5:51 pm Hi Gene, You helped me back in November with a F10 error. Sad news.

I have a Frigidaire gas range model LFGF3014LWC. You may need to replace the overlay as well. I am lost as to how to proceed next as the touchpad was included with the new EOC? Pull the range out of the wall and unplug it.

Here is my previous reply: "Hello Valerie, Thank you for your question. Thanks. Gene. She has had repeated problems with it stopping, locking up in the model of cooking, turning off, etc.