ford error code p0351 Pennington Texas

Computer services provided in your home or place of business at a time that is convenient for you. Please call to schedule your appointment.

Address Nacogdoches, TX 75961
Phone (936) 645-0777
Website Link http://www.ntxcs.com
Hours

ford error code p0351 Pennington, Texas

P0351 Is there anyway to test the ECM before you replace it? Published on Sep 1, 2014This is a good cheap Noid Light Set I recommend-http://www.amazon.com/gp/product/B000...In this video I walk you through the testing for these codes so you can diagnose if the YourMechanic offers certified mobile mechanics who will come to your home or office to diagnose and repair your vehicle. The P0351 code can have some drivability symptoms that will not make it safe to drive depending on how severe the symptoms are.

Leave a comment below or tell us if the information above help you fix the code. Any information is appreciated. Well 4 hours and $90 later they called and said the ECM was bad and for $700+ they could fix it. I have replaced the coil for cylender 1 and the same code still persists.

If not, the PCM is likely faulty. Do this by attaching one meter lead to the B+ terminal on the coil and the other to the coil output tower. I also have a misfire code for cylinder 1 coil. This wastes time and money for repairs.

I don't have the service manual for my Escape yet so I can't be of much help. firemanjonjon View Public Profile View Gallery Find all posts by firemanjonjon #4 02-09-2007, 11:29 PM firemanjonjon New User Join Date: Feb 2007 Posts: 3 I broke down and I've asked before about the ignition coil. The test fails when the ECM does not receive a valid pulse signal from the ignition coil.

Tech notes Ford Ignition Coil Primary Codes P0351-P0360 Diagnostic Walk throughUser Submitted Video What does this mean? Category Autos & Vehicles License Standard YouTube License Show more Show less Loading... Two wires are dedicated to each coil. by Valerie Johnston The Best Used Cars to Buy If You Live in a Tropical Climate by Valerie Johnston How Long Does a Fuel Filler Neck Last?

If the same cylinder sets the code, then perform a compression test on the offending cylinder and check for any vacuum leaks in its area with a good quality smoke machine. F Thanks Perrymac400 View Public Profile View Gallery Find all posts by Perrymac400 #8 02-23-2008, 09:30 PM antony25 Senior User Join Date: May 2005 Location: Omaha, NE Posts: DaddytookmyT-Bird View Public Profile View Gallery Find all posts by DaddytookmyT-Bird #12 04-13-2008, 07:32 AM aalleoxn New User Join Date: Apr 2008 Posts: 2 New member here. touble code p0351 Page 1 of 2 1 2 > LinkBack Thread Tools Search this Thread #1 02-06-2007, 12:59 PM firemanjonjon New User Join Date:

I smelled sulpher smell so I gutted...Help w/ ODB2 code 1999 RodeoHi, New here, heard many good thing about this place and the help that can be had. If manipulating the wiring causes the misfire to surface, repair the wiring problem. Ask a question to our users or find an automotive repair shop near you to help fix the OBDII code Ask a Question Find a Shop Related Information Help AutoCodes.com Help The Engine Control Module (ECM) controls each ignition coil operation.

P0352? Symptoms Symptoms of a P0351 DTC may include: MIL (Malfunction indicator lamp) illumination Engine misfire may be present or intermittent Causes Potential causes of a P0351 code include: Short to voltage Please try again later. Transcript The interactive transcript could not be loaded.

What repairs can fix the P0351 code? just making sure I on right eng. Here's the follow-up. Recall that the PCM intermittently supplies ground to the coil for desired operation.

The ignition coil or coils are responsible for igniting the air/fuel mixture inside the combustion chambers. Do you need more help with the P0351 Ford code? Loading... westisbst 2,729 views 5:26 2002 Ford Escape 3.0 Misfire - ignition coils connected wrong - Duration: 39:06.

Have you replaced any parts? Any information is appreciated. Attach one lead of your multimeter to each terminal on the coil and set the meter to read ohms. Who did you use?

The low voltage side of the system is referred to as the primary circuit. If you don't detect any frequency signal from the PCM on the ignition coil driver circuit indicating the PCM is grounding/ungrounding the circuit (or there is no visible pattern on the Start by disconnecting the coil connector. Then, the current is interrupted by a switching device (usually the PCM).

If however, the misfire remains on the same cylinder, you know the control circuit is to blame. Working... cities. If there is continuity, suspect a problem with the PCM.

still had a check engine light. Thanks Please enable JavaScript to view the AutoCodes.com Powered by Disqus. As I don't have a lot of $ to replace everything, is there a colaborative step by step method to trouble shoot and fix this. Key dance trick and code readers are limited.

As the PCM controls the coil- Have you changed coil? We’ll let the variable x stand in for the last digit throughout this article, as troubleshooting is the same for each of these codes. Have an assistant crank the engine while you monitor the test light. There is a chance you got sold a bad coil.

Switch the entire coil and spark plug as an assembly with a known good cylinder, Clear the code(s) and go for a test drive. It eliminates the need for spark plug wires by putting the coil right above the sparkplug. Tech notes Ford Ignition Coil Primary Codes P0351-P0360 Diagnostic Walk throughUser Submitted Video What does this mean? Testing coil resistance (Courtesy: autozone.com) Check for power Next, check the coil for power.

this is a single coil - and has distributor... JoeTheAutoGuy 67,251 views 39:58 How to Diagnose Faulty Coil Pack - Duration: 2:08. However, when a car is sold, given away or inherited, the title needs... At your home or office Choose from 600+ repair, maintenance & diagnostic services.

You can check whether the PCM is providing ground to the coil with a multimeter set to volts. Note: on some vehicles the engine will have to be cranked during this test. mreinsmith 283,174 views 16:28 2017 Ford Super Duty PRODUCTION - Duration: 10:09. It is true that some of the newer Fords have an issue with the purge valve staying on, putting a vacuum on the system...