floppy disk error messages Palacios Texas

*Licensed And Insured Commercial Electrical Contractors and Cabling Contractors *Commercial & Industrial Maintenance *Phone and Computer Wiring *Security Lighting *New Construction *Light Fixture Replacements *Tenant Build-Outs *Troubleshooting and Repairs AMENITY After Hours Emergency Service Available.

*New Commercial Construction *New Outlets/Circuits *Parking Lot Lighting & Troubleshooting *Bus Duct Installation *Code Corrections *Control Wiring *Design Build *Emergency Service *Network Cabling Systems *Fire Alarm Systems *Generators *Health Care Facilities *High Bay Lighting

Address 5044 Timber Creek Dr, Houston, TX 77017
Phone (713) 921-1368
Website Link http://www.mcdonaldinc.com/
Hours

floppy disk error messages Palacios, Texas

Stand up for your rights!!! Replace the floppy data cable that connects the computer floppy drive to the motherboard \ I/O board. If you believe this post is offensive or violates the CNET Forums' Usage policies, you can report it below (this will not automatically remove the post). STechnovation 218,794 views 2:09 Disk Boot Failure Fix - Duration: 3:02.

not the driver there is no actual place to put floppy disks in. The system's configuration settings are normally checked first. While on the BIOS screen, look for an indication either along the top or bottom designated by one of the function keys (I believe it used to be F10 to restore So far my PC worked fine the entire weekend and hopefully will remain that way.

The above picture illustrates what drive should be connected where. El Torito 43,847 views 4:53 Computer problem, Disk Boot Failure - Duration: 2:49. Before trying to bite the PC in the face or do the ?CrashTest? Flag Permalink Reply This was helpful (0) Collapse - Boot Failure by duvlen / July 27, 2007 4:50 PM PDT In reply to: Boot Errors 1.

In most systems, the BIOS and operating system use plug-and-play techniques to detect new hardware that has been installed in the system. Submitted by: Marlene O.This answer was voted most helpful by our community membersAnswer: Disk Boot Failure - Some Things To Try Marlene,The disk boot failure could come from a number of Hardware failure (physical problem with the boot drive) General Failure Error Reading Drive x Corrupted or missing boot files Bad or Missing Command Interpreter Nonsystem Disk or Disk Error Bad File Autoplay When autoplay is enabled, a suggested video will automatically play next.

I get error messages as "Disk boot failure" "Hard Drive Missing. "Hard drive 0 missing" and some other times "Disk Write Delay Failed". About Press Copyright Creators Advertise Developers +YouTube Terms Privacy Policy & Safety Send feedback Try something new! I ended up replacing the SATA cable to my HD and that resolved the problem immediatellly. These cables are very cheap and whilst HP should fix it all under warranty often the hassle is not worth it.

i currently am running about 12 hard drives including externals, never had a maxtor last more than warrantied (most under 6 mos.), and have yet to have a problem w/a western HP had a now-infamous recall issue back at the early part of 2001-2002 with a batch of Fujitsu brand hard disks. If the error occurs after the CMOS screen displays and before the bootup tone, you must clean boot the system and single-step through the remainder of the bootup sequence. GEEKS TO GO IS THE WAY TO GO!

These problems result from mismatches between the system's programmed configuration held in CMOS memory and the actual equipment installed in the system. Formatting and/or recovering the drive will most likely not correct an error of this type. If the floppy drive is not setup properly you may experience read/write errors or the floppy may not work at all. Flag Permalink Reply This was helpful (0) Collapse - Replace the SATA cable by Fat_Aido / December 14, 2013 6:56 AM PST In reply to: Yes, I replaced the sata cable

Eliminating possible conflicts with other hardware If you have recently installed any new hardware, you should consider disconnecting it temporarily it to ensure that it is not the cause of your Thanks! But I happened to have a spare SATA cable lying around, and for the heck of it, tried replacing the cable. Ultimately, if you were to pick up (or could somehow borrow) a different IDE cable to test for a short time it may also call out a failed or failing cable

Ask ! Additional information Unable to read floppy diskette. Forum Floppy disk(s) fail (40) Forum "Floppy Disk(s) fail (40)" ????? If that is ok, and set properly already, then I would suggest making sure that your computer is able to read from all the drives properly.

unplug the power cable of my PC2. Username or email: I've forgotten my password Forum Password Remember me This is not recommended for shared computers Sign in anonymously Don't add me to the active users list Community Forum What does this mean exactly? Save/backup your email, your documents and pictures and music.2.

i disable integrated LAN and no error halt 0 #12 bigbearvengeance Posted 06 March 2011 - 07:40 PM bigbearvengeance New Member Member 1 posts Back to the floppy disk (s) fail and what has happened since it last worked? 0 #6 andrewasmith1 Posted 28 June 2005 - 01:22 PM andrewasmith1 Member Topic Starter Member 32 posts Thanks guys problem fixed. do not bother trying to backup your programs because generally they need to be installed not just copied back.3. In these cases, the user must manually resolve the configuration problem.

If your floppy cable has more than one connection, verify that you have connected the floppy to the appropriate connection. You're allowed only a few moments to press the required key before your operating system starts to load. I have same errors. The only thing left is to wipe my hard drive and do a system recovery.

If you do not have a tab place tape over this hole. Jeff James 22,556 views 2:49 Hard Disk Boot failure Solved for Win Xp - Duration: 3:01. Flag Permalink Reply This was helpful (0) Collapse - Try replacing the hard drive interface cable! Flag Permalink Reply This was helpful (0) Collapse - Also make sure you didn't leave any floppy discs or CDs in by Technojunkie3 / July 27, 2007 1:13 PM PDT In

Several functions may not work. You might save yourself lots of $$$, like I did! Never had this problem using IDE drives. Do I need a boot disk or a full system restart?

It is possible that the Boot options set up in the system CMOS are not set up properly, or may have been changed, normaly this wouldnt happen for a new computer, betterundefinedxx 332,002 views 3:02 Loading more suggestions... Watch Queue Queue __count__/__total__ Find out whyClose How to fix a floppy disk boot failure Michael Bezuidenhout SubscribeSubscribedUnsubscribe1212 Loading... Restart the computer, If the computer wont boot from the floppy disk, then it is probably because the boot sequence has been changed, which is why you may get the error

One thing I do to "TEMPORARILY" fix this problem is: 1. Sign in Statistics 23,708 views 47 Like this video? If the configuration settings are correct, but these symptoms are present, a hardware problem is indicated as the cause of the problem. Or should i allways try & Backup & set a new System Restore?Thx For Any Questions & Help ;-)[email protected] & State You'r Msg.

Not connected properly Power down, unplug, and open computer, being aware of ESD and its potential dangers. Hopefully you have the system installation disks to restore your system software. Thank You!