frigidaire gallery oven f11 error Shawanee Tennessee

We offer: Website design and hosting Networking services Virus removal Server and computer repairs Data backup and retrieval Hardware and software troubleshooting Remote services available.

Address Morristown, TN 37814
Phone (423) 258-5000
Website Link

frigidaire gallery oven f11 error Shawanee, Tennessee

Loading...Oops :Please try again. What does an F11 code mean and how can I get the beeping to stop on my Frigidaire gas oven? Report This by Manage My Life March 22nd, 2009 I would In such situation the solution is to replace the Electronic Oven Control (EOC). Not finding what you are looking for?

We were cooking and all of a sudden the error message came on. My questions: 1. model #GLEF378ABC. Used the new plug and its wires from the new wiring harness.

We have to... I hope this is helpful information. -Matt Feb 25, 2015 | Frigidaire Kitchen Ranges 1 Answer My stove won't stop beeping and has a FC error code - can I stop Gene. Add your answer Sign in to answer a question 1 Answer from this member: The constant beeping and the F11 are caused by a shorted touch pad.

If the reading is incorrect and the wires and plugs between the sensor and the EOC are good, replace the temperature sensor (RTD probe). If there are some relays on it, replace the EOC. If this error code shown while the oven was in day time mode, the EOC would need to be replaced. I am still receiving the repeating F10 error code.

Our oven flashed F10 and went into runaway temps. MML // Mar 31, 2015 at 4:09 pm Hi Gene, Thanks so much for your reply. When we set a temperature at say 350, it beeps between 25 to 50 degrees less (we used an oven thermometer for testing). Keep me posted.

The part number for the oven relay board is 316443920 The part number for the EOC is 316576601 Good luck. Just put in Kenmore range. To test the resistance value of either potentiometer make sure that the shaft is set to the off position, disconnect the wire harness and use an ohmmeter to measure the resistance Codes flashing are F 7 and 20.

I verified this was the case by removing the upper rear panel of the stove and disconnecting the keypad connector from the upper left of the lockout board. There suppose to be one more letter at the end. any thoughts would be welcome. Check for continuity between the two probe wires.

Sure would like to find a cheaper fix! Yes, the temperature sensor tests OK. kimberly // Feb 26, 2015 at 6:22 pm Hi I have a frigidaire gas oven model LFGF3014LBC and have been getting f10 error for a while and now just started getting The oven was working fine until in the last couple of days the PF code would come on after the oven had been on for a while.

I don't have "speed bake" on my oven model. The part number for EOC is 316557115 You may want to replace the overlay as well because the old one can be easy damaged. Gene // Jan 4, 2015 at 1:07 pm Hello Eric, If the problem just melted wire harness connector and the temperature probe tests out OK then the easiest solution is to Sounds like like from what I read online that I might need a new relay.

Ed // May 5, 2015 at 7:19 pm Hi Gene. Step 2: Please assign your manual to a product: About Advertising About Us Blog Careers News & Media Help Contact FAQ Partners Privacy Policy Terms Community Forums Recent Q&A Top Experts If the potentiometer failed any of the tests, it would need to be replaced. How did you fix the problem back in April?

Valerie // Dec 19, 2014 at 11:49 am Hi Gene, The model number for the range is CEW30EF6GSC. Expand» Details Details Existing questions More Tell us some more Upload in Progress Upload failed. With the diagnostics above, I was able to pretty quickly determine that the EOC was bad. Wird verarbeitet...

Any help would be greatly appreciated. Gene. Frank // Nov 4, 2014 at 3:56 pm I have an Electrolux model#EW30DF65GSB. Gene.

I checked the sensor and and it checked at 1100. reholton49 Apr 02, 2013 My range started the beeping and F11 failure today and the tec assisted my by having me to tkurn flick off the breaker for 2 mins. ft. ... Still not working but the igniter fires up now.

If open, replace Lock Motor Assembly. 5. (F90, 91, 92, 93 & 94) Lock Motor continuously runs - if Micro Switch is open, replace Lock Motor Assembly. 6. (F92, 93 & Power up the stove. none stop beeping. Gene.

Mayor: An expert whose answer got voted for 2 times. I have a quick question you may be able to answer. Any suggestion is highly appreciated. Denise // Jun 15, 2015 at 1:38 pm Hi, Gene, I have a PLEs39ECG, serial NF73726 that gives me an error F30.

Gene // Dec 26, 2014 at 2:29 pm Hello Rick, This problem can be caused by a faulty temperature sensor as well as a faulty relay board. Have a manual for Kitchen Ranges? Code Cause - Condition Suggested corrective action F10 Control has sensed a potential runaway oven condition. It is just run away heat.

mirleiser Apr 13, 2009 We had this happen tonight. What does this mean please? It is located behind the control panel. When power is restored, if your stove is still beeping, I suggest contacting your local authorized technician.

Thanks. The RTD part number is 316490001 The EOC part number is 316418704 Thank you for your question.