ford fiesta engine error codes Pleasant Shade Tennessee

Address 301 Times Ave, Lafayette, TN 37083
Phone (615) 688-4772
Website Link

ford fiesta engine error codes Pleasant Shade, Tennessee

VAG 3,4,5, and P1 Codes along with many other Manufacture Specific Codes! Therefore, a low AIR circuit indicates a driver is always on and a high circuit indicates an open in the PCM. The test fails when the adaptive fuel tables reach a rich calibrated limit. Access KOER diagnostic trouble codes on scan tool.

Username Forum Password I've forgotten my password Remember me This is not recommended for shared computers Sign in anonymously Don't add me to the active users list Privacy Policy Follow Us Open circuit in harness Sensor signal short to power Improper harness connection Damaged sensor Damaged PCM Monitor IAT2 PID. Test always off - SCB signal or VPWR open in harness or PCM. If during key ON engine running the air flow (or voltage) changes below a minimum calibrated limit, the test fails.

Leaking diaphragm or EVR. Damaged wheel speed sensor harness circuits. Remember, these are manufacturer specific codes only. CMP circuit open CMP circuit short to GND CMP circuit short to PWR SIG RTN open (VR sensor) CMP GND open (Hall effect sensor) CMP misinstalled (Hall effect sensor) Damaged CMP

AIR circuit open AIR bypass solenoid fault Damaged PCM AIR circuit short to power Solid state relay fault Damaged AIR pump The AIR circuit is normally held high through the AIR Recent Ford OBD-II forum topics1998 ford ranger code p1740 & p17412006 Ford Focus Code P2258 air pump, P0202Ford ranger 2.2 6 speed U0418 and U0001What is code P1506 on a 98 This condition will cause the boost from the supercharger to be bypassed to avoid potential engine damage. P0125 Error Description Insufficient Coolant Temperature For Closed Loop Fuel Control Indicates the ECT or CHT sensor has not achieved the required temperature level to enter closed loop operating conditions within

P0100 Mass or Volume Air Flow Circuit Malfunction P0101 Mass or Volume Air Flow Circuit Range/Performance Problem P0102 Mass or Volume Air Flow Circuit Low Input P0103 Mass or Volume Air If you find one missing let us know and we we'll add it immediately! Water in harness connector. On most vehicle applications the malfunction indicator lamp (MIL) will be triggered when this DTC is set.

It is not intended as repair advice and we are not responsible for any actions you take on any vehicle. These are for SAE standard ones, as used for SAE J2012 OBD-II: Anatomy of the Diagnostic Trouble Code A DTC is made up of 5 digits. Note: On engines which are equipped with an oil temperature sensor, the PCM reads oil temperature to determine if it is excessive. E510.

Improper harness connection. They are listed below with Type A being the more severe. High fuel pressure (caused by damaged fuel pressure regulator) NG. Damaged PCM.

Note on some vehicles that are not equipped with an ECT sensor, CHT can be used and can set this DTC. EOT V PID reading greater than 4.5 volts with key ON and engine OFF or during any engine operating mode indicates an open circuit hard fault. Theres a post in this thread here in which Richt mentions that he'd pm'd the fault codes to someone: might be worth contacting him. _________________________ Top #49972 - 12/07/06 10:07 PM P0460 Error Description Fuel Level Sensor Circuit Malfunction The PCM monitors the fuel level input (FLI) circuit for electrical failure.

Check wiring and connector for damage. Let's go! EGR sensor D.P.F. Here's a generic list of DTC codes for reference, makes the post a bit long but should do.

DTC P0116 is set when all of the following conditions are met: Engine coolant temperature at engine start exceeds IAT at engine start by more than a calibrated value, typically 30°F P0116 Error Description Engine Coolant Temperature Circuit Range/Performance Failure Indicates the engine coolant temperature rationality test has failed. Intake Manifold Runner Control fault P1530 Open or Short to A/C Compressor Clutch circuit P1537 Intake Manifold Runner Control Stuck Open P1538 Intake Manifold Runner Control Stuck Open P1539 Power to Share this post Link to post Share on other sites Brijohng56    1 Settling In Well Budding Enthusiast 1 48 posts Name: Brian Ford Model: Focus convertible 58 plate Ford Year:

P0172 Error Description System to Rich (Bank 1) The Adaptive Fuel Strategy continuously monitors the fuel delivery hardware. Base Engine: Oil overfill. P0231 Error Description Fuel Pump Secondary Circuit Low NOTE: For natural gas applications, the following description applies to the fuel shutoff valve monitor (FSVM) and the fuel shutoff valve power (FSV However there are external items that can cause this DTC.

Induction system: Air leaks after the MAF. Vehicle is new from the factory Battery or PCM had recently been disconnected An OBD II monitor failure had occurred before completion of an OBD II drive cycle PCM DTCs have Below you will find the most complete list of Ford trouble codes available. Low ambient temperature operation.

and many bananas. P0234 Error Description Supercharger Overboost Condition The PCM disables (bypasses) the supercharger boost and sets a diagnostic trouble code (DTC) to keep from damaging the powertrain (engine or transmission) during potential If you want to share this article or information with others, please link to this page, don't copy and paste it elsewhere. © 2004-2016 Home Articles Generic OBD-II Domestic Damaged PCM.

Problem (Low Input)P1144 Mass Air Flow Sensor Open/Short To GroundP1145 Solenoid Valve Running Losses Control Circuit ElectricalP1146 Pressure Sensor Circuit Range/Perf (High Input)P1147 ETS Sub Accel Position Sensor 1 MalfunctionP1148 Closed Very high engine rpm for extended period of time. X X X X X B-Body C-Chassis P-Powertrain U-Network 0-SAE 1-MFG 1-Fuel and Air Metering 2-Fuel and Air Metering (Injector circuit) 3-Ignition Systems or Misfire 4-Auxiliary Emission Controls 5-Vehicle Speed Control