ftp use socket error 10060 Sullivans Island South Carolina

Address 745 Johnnie Dodds Blvd, Mount Pleasant, SC 29464
Phone (843) 884-7267
Website Link
Hours

ftp use socket error 10060 Sullivans Island, South Carolina

Now restart WWW publishing service by going to start, run and type cmd. If you still receive a 10060 error, the server may be trying to send a listing for a very large directory (with many thousands of files) causing the client to time-out Socket Error # 10038: If you are using Serv-U modify your FTP server settings so that the following are unticked: “Block anti time-out schemes”, “Block FTP_bounce attacks and FXP”, and “Block ERROR:> Can't connect to remote server.

Verify that the destination host name or IP address is correct and try again later. Socket Error # 10039: There may be a problem getting the IP address for the hostname. To do so, you will also have to modify the registry. Copyright © 1996-2011 GlobalSCAPE, Inc.

If you are using a router, verify the router is up and running (check by pinging it and then ping an address outside of the router). In the Port box, type the correct port number. A connection attempt failed because the connected party did not properly respond after a period of time, or established connection failed because connected host failed to respond.’ Solution Download Available to The most common cause is an incorrectly configured server, full server, or incorrect Port specified by the client.

Method 4: Configure Firewall Settings Sometimes the error may also occur due to Firewall.  To resolve, configure Firewall settings to allow FTP protocol. If you see an error log similar to the one below, in the Site Properties of the problem site, click the Type tab, then change the Data Connection Type to Use Socket error = #10060 10060 is a Connection Time-out error that usually appears when the client does not receive a response from the server for a specific command. To confirm changes, click OK.

if you have entered something like ftp://my.hostname.com/ then change it to my.hostname.com Socket Error # 10061, Connection refused: The hostname is correct, but either the FTP server is not listening on All rights reserved. Try reconnecting at a later time. Eventually the selection window appears but it’s empty: You need to enable Passive mode, or the FTP server is behind a firewall that is not configured correctly.

If required, please consult your firewall administrator or vendor for advice. Remember serious problems may occur if you modify the registry incorrectly. If you are using implicit SSL then you probably need to use port 990 instead of port 21. It is generally caused by either outgoing connection problems or connection problems on the host end.

Socket Error 10060 is basically a connection time-out error. The remote host actively refused the attempt to connect to it. Method 5: Download Total System Care Whether the error occurs due to viral infection or registry issues, it is advisable to download Total System Care. Method 1: Troubleshoot the Web Proxy Connection This method is workable and effective if Socket Error 10060 occurs only when the web proxy service is used.

This is done to pass the correct IP address, for example. If you still receive a 10060 error, the server may be trying to send a listing for a very large directory (with many thousands of files) causing the client to time-out Do a traceroute to the destination to verify all routers along the connection path are operational. Verify that your subnet mask is setup properly.

Verify that the destination server name or IP address is correct Verify that the connection port number is correct (under Site Settings > Type tab). If using a local server table for server name resolution, check to see that it doesn't resolve to an obsolete address. It is safe, user-friendly and compatible with all Windows versions. Error Tools Editor's Choice.

If you’re using a Dynamic DNS program with your FTP server you may find that disabling passive in the DNS settings (and FTP server) and in SyncBack/SE will fix data transfer Now on the type tab change the data connection type to use port. Method 2: Increase Web Proxy Time out Settings If disabling the web proxy settings doesn’t work, then try increasing time out settings. Verify that the destination IP address and port numbers are correct.

To execute it, here’s what you need to do: install the Winsock Proxy Client on your PC. WSAETIMEDOUT (10060) 10060 is a connection-timeout error that usually appears when the client does not receive a response from the server for a specific command. It cleans, repairs and restores the registry while the antivirus removes all types of viruses like spyware and Trojans in seconds thereby resolving socket error code 10060. How to Resolve Socket Error 10060 Home > Windows > How to Resolve Socket Error 10060 PC Support Hotline: 1-844-377-4107 Fix Socket Error 10060 Socket Error 10060 - What is it?

COMMAND:> LIST STATUS:> Connecting ftp data socket xxx.xx.xxx.xx:xxxx... Registry issues Viral infection Further Information and Manual Repair Here are some of the best and quick DIY methods to resolve Socket Error 10060 on your PC. Verify that you have chosen the right protocol (SSH2, SSL, FTP, etc.) and have setup all required options for that protocol. The connection fails due to an error or timeout.

Error Causes Socket Error 10060 may occur due to multiple reasons including: Blocked port Data connection incorrect settings When the web proxy connection setting does not allow enough time to receive Disable the web proxy settings under the LAN settings on the Connections tab of the internet options. Here’s what you need to do, click start, run and then type ‘regedit’ in the dialogue box. Socket error = #10060.

Switch to the opposite data connection type (PASV or PORT) under Site Settings > Type tab. Also, enter the hostname or IP address, not a URL, e.g. If you continue to receive the same error after insuring ports 20 and 21 are open, please contact the administrator of the site where you are trying to connect. Outgoing connections can be affected by the presence of firewall or anti-virus software on the local computer or network connection.

Either can block the ports needed to make a successful FTP connection to the remote server. The registry cleaning utility removes junk files, cookies and invalid entries damaging the registry. The remote server may be refusing multiple connections from the same client. Unable to connect: Connection time out: The hostname may be incorrect or the FTP server may be behind a firewall.

For further information you may be interested in these similar issues: A Guide to Quick Fixing Error 10013 How to Fix Error 12031 How To Easily Fix Unresponsive Script Posted by: Once you disable the settings, then try to go to the website that you giving you the error. You could not make a connection because the target computer actively refused it. Socket Error # 11004, Unable to connect: Check to make sure there isn't a trailing or leading space character on the FTP hostname.

Socket Error # 10093: This can happen when the network connection goes down, e.g. CuteFTP uses passive mode by default so to ensure the error is resolved, you may have to switch from passive mode to active port mode. For a regular FTP session, either disable the firewall or anti-virus software or configure them to allow CuteFTP to establish an FTP session over ports 20 and 21. the FTP server is no longer connected to the network.