fc error codes Little Compton Rhode Island

Address 211 Airport Access Rd, Middletown, RI 02842
Phone (401) 846-9400
Website Link http://www.avports.com
Hours

fc error codes Little Compton, Rhode Island

F9 - Oven Door Lock Failure - Check door lock switches and wiring. Check wire harness connections to the drain pump, pressure switch, and Central Control Unit (CCU). 4. Note: Applies to all F1-E... All rights reserved.

Check door switch/lock unit. 3. The failure will be reset after running the Diagnostic Test Program is run. 1. Find Parts Whirlpool Duet Front Loading Automatic Washer Fault Codes Failure Code Fault Code Description Solution FH No water detected entering machine or Pressure switch trip not detected. Mesquite, TX "When you say 'Fast Shipping', you aren't kidding!" Warnie M.

Some models incorporate keypad in to control board as one unit. Unplug washer or disconnect power. 2. Disconnect power and unplug unit to check door switch/lock unit. Exchange steamer electronic board if valve is OK.

To compare sets of files, use wildcards in pathname1 and pathname2 parameters. Unplug washer or disconnect power. 2. S. Replace motor controller.

Select the 'cancel' function and wait 60 seconds. Allow at least a minute after power has been restored and if error code reappears, replace control board (clock). F3 Oven temperature sensor (RTD) open Replace Oven temperature sensor (RTD) F4 Oven temperature sensor (RTD) shorted Replace Oven temperature sensor (RTD) F5 Board failure Replace control board (also called ERC codes.

F7-E1 - Common Switch Wire Is Defective - This error occurs when common wire to latch switch and door switch is shorted. Check wires and connectors from control to latch switch, then from latch switch to control. Unplug washer or disconnect power. 2. Verify CCU operation by running a Diagnostic Test or any cycle.

Replace if zero or infinite ohms. Press 'Stop/Cancel' to clear display. Press CANCEL. Check Pressure Switch harness for continuity. 2.

Press PAUSE/CANCEL twice to clear the display. F05 - Water Temperature Sensor Error - Unplug and disconnect power to the unit and check all connections to the water temperature sensor, heating element and element relay. Replace also the CCU. Replace sensor if found defective.

Check probe. Check the wire harness connections to the Motor Control Unit, Central Control Unit, and Interference Filter. 3. Check the drive motor for powered rotations. 8. Home RepairVideos Top Load Washer Front Load Washer Electric Dryer Gas Dryer All Repair Videos Troubleshooting Dishwasher Electric Dryer Electric Range Front Load Washer Gas Dryer Gas Range Microwave Refrigerator Top

Check the wire harness connections to the Central Control Unit (CCU) and the door switch/lock unit. Verify CCU operation by running a Diagnostic test or any cycle. Push the door and check if it is completely closed. 2. Verify CCU operation by running a Diagnostic Test or any cycle. 6.

Press STOP/CANCEL to clear the display. Unplug washer or disconnect power. 3. Replace probe if all else checks out ok. F3 Key panel (touch pad) shorted This code will occur if a shorted key panel is detected continuously over 60 seconds.

F32 PRESSURE SWITCH FAILURE If there is no electrical supply to the Pressure Switch from the CCU or if the Pressure Switch contacts are worn out, then a Pressure Switch Failure Door switch open while door is locked. 1. F64 STEAMER INLET VALVE FAILURE The Steamer valve or fl ush valve is blocked open or not working properly. Melde dich bei YouTube an, damit dein Feedback gezählt wird.

Check pins 1 and 5 of P16 of the machine controller and pins 1 and 2 of P1 of the motor controller. Look for condensation or contamination on probe receptacle. Press PAUSE/CANCEL twice to clear the display. Unplug washer or disconnect power. 3.

If there is water in the unit, verify the drain pump is working and the pressure switch hose is in good condition and properly connected. Press 'Stop/Cancel' to clear display. NOTE: To find correct Ohm reading refer to the Water Temperature Sensor section. 1. Check for continuity of the User Interface harness. 2.

If connections are ok, then check individual switches as outlined for the F5 error code. Copyright © 1999-2016 , Eldis Group Partnership. Unplug washer or disconnect power. 3. This should have AC line voltage when the motor controller is powered.

Check wire harness connections to pressure switch, drain pump, and Central Control Unit (CCU). Check dispenser motor for powered rotations. Fault Codes Fault Codes Admiral Bosch Dacor Estate Frigidaire GE Gibson Hotpoint Jenn Air Kelvinator Kitchen Aid Magic Chef Maytag Roper Sears / Kenmore Tappan Thermador Whirlpool We are Safe, Secure, Replace CCU board.

Check that NTC resistance of the Steamer is in range between 170 kΩ and 300 Ω, refer to Temperature Sensor table.If resistance is 0 Ω or infi nite value, replace NTC. F11 MOTOR CONTROL UNIT ERROR The Motor Control Unit has internal failure; repeating under or over voltage, or over current conditions. F29 DOOR UNLOCK ERROR If the door unlock has failed 6 times. F2 will appear.

Check the inlet valve for proper shut off. 7. The door may now be opened. F1 Stuck touch pad Usually means that either the touch pad or the oven control (also called clock or ERC) is defective and needs to be replaced. Sud SUDS LOCK (OVERDOSE OF DETERGENT DETECTED DURING THE WASH CYCLE) If suds are detected continuously by the pressure switch during the drain or spin phases, the washer will fill 4