geo metro error code 51 Winston Oregon

Address 1737 Byron Creek Rd, Winston, OR 97496
Phone (541) 679-6122
Website Link

geo metro error code 51 Winston, Oregon

I remember the first time that I blew air through the two ports covered by the EGR valve, I had good air movement back toward the exhaust manifold but no air I have played the flasher switch back and forth, but the turn signals have not worked yet. Diagnostic Trouble Codes (DTC) may be accessed by installing a spare fuse into the fuse box diagnostic terminal, located under the LH side of the instrument panel, then turning the ignition All trademarks are ownership of their respective holders.

They went through all the testing and it past. thinks up wild ways of doing it. Chevrolet Spectrum I need to replace the blower motor but can't get the glove box to come out, how do I remove it, I'm told that's all I need to take Code 51 says you have a gross failure to detect that EGR action.

I have been having issues with it. called back up strategy. Suggested Questions/Answers : My battery died on my 2003 tiburon and i tried to boost it and the lights start blinking and the siren goes off but the car won't start I don't think the block itself has any passages in it does it?

That or your have another oil leak somewhere. I love this car because first, I'm a tightwad and I love 45 to 48 mpg, and secondly, I intend to drive it until it falls over and dies an unnatural When you clean out the passageway in the 2nd section you will want to be able to see your reaming tool protrude as coming out of the egr-valve entry port each I cleaned it out thinking I had found something that might be connected to the EGR problem. Truck European Import Domestic Manufacturer The network consists of the largest network of enthusiast-owned enthusiast-operated automotive communities. It is time I attempted to contribute, by offering a solution to a common Check Engine fault that, hopefully, can benefit others, just as you folks have benefited me. Password Register Home Forum Active Topics Photo Gallery Garage Garage Garages Browse by Username Browse Recently Added Browse Recently Modified Browse Most Popular Advanced Search Help Today's Posts Auto EscrowAuto LoansInsurance Am I correct?

Sparky Feb 16 2010, 06:14 PM Post #15 Elite Member Posts:155 Group:Members Member#1,829 Joined:Feb 13, 2010 LocationCentral TexasYear/Make/Model1994 Geo Metro 1.0, 5 speed three door idmetroFeb 15 2010, 10:10 PMSparkyFeb 15 A intermittent engine misfire to a camshaft sensor problem. eg: ecu commands EGR open. I have, according to all the diagrams, the "enhanced" emissions system.

Sensor so REGT is Recirculated Exhaust Gas Temp.If you pull your EGR and start the engine you will get vacuum and air pressure. Reconnect the negative cable to the battery, and voila, you will be pleasantly surprised. [email protected] 08-16-2007, 09:42 PM #6 (permalink) jtgh Banned Join Date: Apr 2007 Posts: 9,643 Gallery: 0 tinker can you tell me what year has this thermal sensor? I blew out all the passages (clean) and replaced all the vacuum hoses to each component.

We upload enough of them eventually we will get it right.Dare we say, not all Code 51s are the same.... We learned about that in the late 80's. What is the solenoid coil? One thing that I wonder about is that about 5 or 6 days ago I had a code 23 which is the IAT sensor code.

No luck. Yes, I put a vacuum guage on the line and as I increase engine speed the vacuum increases from the flow of exhaust gases. I am interested in all EGR monitor methods. make sure the tiny filter on the line is clear.

Last edited by jtgh; 10-12-2007 at 09:09 PM. 06-15-2009, 09:54 PM #9 (permalink) 1.6_Sami Newbie Join Date: Jun 2009 Posts: 11 Gallery: 0 Quote: Originally Posted by jtgh However, two different lamp functions can occur when the engine is started. This means you are limited to certain areas of the board and there are features you can't use and images you can't see. some cars with out MAF can do it this way. (8 valve this era) they are just reading the AIR TEMP sensor rise?

Like Bookmark January 7, 2009 at 12:57PM Thank you for reporting this comment. Now with about 2500 miles on the head job I get a code 51. Bad Bent Feb 15 2010, 08:24 PM Post #9 Facetious Educated Donkey Posts:14,722 Group:Moderator Member#334 Joined:Dec 26, 2008 LocationNative of SoCal, in Moscow, IdahoYear/Make/Model1991 and 1996 Geo Metros OK, so Johnny The most difficult section is the 3rd section to the intake manifold plenum.

Also PO442. Oh, by the way, do clean the pcv valve also. I still get a code 51 after about 10 miles of freeway driving. IÂm now selling my car and I need to clear the check engine light so it can be smogged for the buyer.