f06 error code kenmore washer Farris Oklahoma

Address Wright City, OK 74766
Phone (580) 319-6797
Website Link
Hours

f06 error code kenmore washer Farris, Oklahoma

Page 1 of 5 123 ... Okay Or call now for immediate assistance: 1-800-252-1698 Thank you! check the wire harness connections between the motor control board (mcu) at the bottom of the washer and the motor. Valid for standard ground shipping within the continental United States and not valid for shipments to Alaska, Hawaii, Puerto Rico, Guam and the US Virgin Islands.

if the wiring connections are okay, i recommend that you check the resistance of the motor windings. The description above sounded like more of a controller issue but since you had already replaced that I would assume that eliminated that component as a potential culprit. Transkript Das interaktive Transkript konnte nicht geladen werden. It is the motor speed that needs to be tested if it does not work right, the washer will stop.

I also noticed the Sears Tech's have trouble figuring out what is causing this error. After that, you might try unplugging then plugging it in again. I replaced the Motor Control Unit with one purchased from eBay, and so far the error has not returned and I've used it on large loads with High Speed spin. 11/01/2013 Drying, 10/14/2016 10/14/2016 JACUSTOMER-x0uwnnmp- Whirlpool refrigerator model GX5SHDXVQ02.

The Italian company that manufactures these babies isn't particularly reliable when it comes to shipping you parts that actually work. Anything that avoids calling repair, right? Check the wire harness connections between the motor control board (MCU) at the bottom of the washer and the motor. Michael, September 29, 2013 is there anyway to get a service manual?

You should measure about 6 ohms of resistance through each winding in the motor as shown below. Discount will be automatically applied during check-out. I recommend that you unplug the washer and remove the back panel. Yes No Voted Undo Score 0 Cancel Add a comment 0/1024 Cancel Post comment Are you sure you want to delete this zzzzzz?

Die Bewertungsfunktion ist nach Ausleihen des Videos verfĂĽgbar. the instructions are accurate in the answer above. Front Load Washer ... Fred M, October 01, 2013 thank you for your question.

A new module costs between $200 and $300, so have your wallet ready. Other "Experts" claim that the motor is fine if the tachometer ohms out other than between 500 and 700. click on "get started" and follow the directions, click on the red "next" button to continue. replied4 years ago.

Connector 1 - is the serial communications link between the MCU and CCU and has three wires. while you are waiting for an expert to respond i was able to locate some great information that could possibly assist you with your issue. To me I think they have a easier was to clean this trap out. Your model has been added.

RepairClinic.com Jake Appliance Repair School 1987-1988 Star Appliance Tech. 2 yrs. 1988-1990 Wards Appliance Tech. 11 yrs. 1990-2001 Sears Appliance Tech. 4 yrs. 2001-Oct. 2005 Jake's Appliance Repair Nov. 2005-present Look-Up Was this answer helpful? So line noise can get into zero-cross detector that measures output frequency. October 5th, 2006,11:32 AM #10 Jake View Profile View Forum Posts Visit Homepage Appliance Tech - Admin Join Date Aug 2004 Location McMullen Valley, Arizona Posts 79,561 Yes, RepairClinic.com will refund

Save model in your profile permanently Don't have a profile? by LYLE W. the image below shows the motor connector and the wiring diagram for this type of washer. When I replaced the CCU with the new part I still received the same message.

i recommend that you unplug the washer and remove the back panel. i recommend that you unplug the washer and remove the back panel. Learn More guaranteed fit All parts are manufacturer-approved, to ensure proper fit and to keep appliances running for years to come. What does the F06 error code indicate on a Kenmore Elite HE3 washer model 110? Report This by Manage My Life April 2nd, 2009 My young daughter has a Kenmore Elite

this can indicatea problwm with the motor or motor control. the image below shows the motor connector and the wiring diagram for this type of washer. Because after verifying the motor windings, tachometer, and motor cable harness, I tapped the tachometer output sensors at the motor control unit (MCU) and connected it to an AC-coupled (but grounded) Fred M, October 01, 2013 thank you for your question.

Yes No Voted Undo Score 0 Cancel Add a comment 0/1024 Cancel Post comment Are you sure you want to delete this zzzzzz? You have reached the maximum number of models that can be added to your list. Starting with the connector at one end, disconnect it, examine the connector and wires for any possible damage, then reconnect it, being sure that any hold-in clips snap back into place. Use our finder Choose your product type Select Select Cooktops Dishwashers Dryers Freezers Microwaves Ovens Ranges Refrigerators Washers Common model number plates Plate location Common model number plates View sample model

Why? This is a normal thing because of how long the cycle is. Was this answer helpful? click here to view.

How can I determine the cause of error code so I order correct part. this can be a difficult problem to pin down. The problem is neither a motor nor a door-latch switch nor a central control module. The repairman told her that she purchased the washer 3 years ago, so her warranty is up and that it would cost her more than the price of a new washer

Learn More guaranteed fit All parts are manufacturer-approved, to ensure proper fit and to keep appliances running for years to come. Unplugging it sometimes corrects the problem. Please report back here if the motor ends up not being the problem. Top Load Washer - White See Details Kenmore 84422 3.4 cu.

The washer starts to add water, then starts blinking, then goes to the error message. Michael, September 29, 2013 is there anyway to get a service manual? If that doesn't help, try visually checking the CPU board for damage or blown parts. Was this answer helpful?