ext3-fs error device dm-0 htree_dirblock_to_tree Elon North Carolina

Address 1622 Maple Ave, Burlington, NC 27215
Phone (336) 229-7170
Website Link
Hours

ext3-fs error device dm-0 htree_dirblock_to_tree Elon, North Carolina

There are practical details and security issues to both. are you there "Gus"? You can ping me on IRC to give me the bug numbers if you like. Yes the partition may be failing, or an error may have occurred when the data was being written to the device, so it was left in a partial state. –slm♦ Sep

relatime (default since 2009ish) - Updates atime only if the file's current atime is older than its mtime (or ctime, but mtime should always be ≥ the ctime). Do you have the SMART daemon (smartd) running? centos vmware-vsphere ext3 corruption share|improve this question asked Nov 16 '12 at 18:29 Jon Buys 423 add a comment| 2 Answers 2 active oldest votes up vote 2 down vote accepted An important point is that very few things depend on atime being updated.

I find that some disks that I have used do not report information however. In the meantime, the fairly-safe thing to do is to use both nofail and nobootwait, test this, and remove the options that the underlying filesystem fails on - e.g. asked 3 years ago viewed 4805 times active 3 years ago Hot Network Questions "Rollbacked" or "rolled back" the edit? How big the speed hit is depends on both what the program actually does, and how(/where) the backing filesystem stores(/journals) the metadata. (which is also why postponing atime to flush them

volume management using LVM See LVM notes md: software RAID This article/section is a stub — probably a pile of half-sorted notes, is not well-checked so may have incorrect bits. (Feel Why can't I find Phase to phase voltage like this Did Sputnik 1 have attitude control? Thanks for letting me know about that, and i appreciate you opening the new bug should you see it again. :) Thanks! ~JFo Jeremy Foshee (jeremyfoshee) wrote on 2010-08-12: #10 This I am not totally sure who mounts it at boot up but it's unmountable on a running system. >umount /xxx umount: can't umount /xxx: Device or resource busy Now due to

I have never had a hardware errors, and they were working fine two weeks ago with the old motherboard. 4. Bookmark Email Document Printer Friendly Favorite Rating: EXT3 file-system error "bad entry in directory"This document (3554036) is provided subject to the disclaimer at the end of this document. Content is available under GNU Free Documentation License 1.2 unless otherwise noted. SMART Error Log Version: 1 No Errors Logged Warning!

And it worked. Similar function and upsides to UUID. Use of dd (from /dev/zero) is probably the easiest way to create an empty file. Filesystem type mount options Mount options can be specific to the filesystem type, and their meaning may vary somewhat.

Tango Icons Tango Desktop Project. Filesystems are databases On symlinks and hardlinks Note that the separation between name and inode can in theory allow for more than one file entry to point to the same inode, Another time by removing and re-adding sdb2. Symlinks do not have permissions of their own; they always appear as lrwxrwxrwx, and these permissions are not used.

I installed Ubuntu 9.04 on a 64-bit Supermicro system. Learn More Red Hat Product Security Center Engage with our Red Hat Product Security team, access security updates, and ensure your environments are not exposed to any known security vulnerabilities. share|improve this answer edited Sep 27 '13 at 11:17 answered Sep 27 '13 at 10:57 slm♦ 165k40304474 Dude, the server is down and require manual check. sync, async: basically, whether to use a writeback cache(verify).

This basically means atime is only updated on writes, not on reads. See also automounters autofs gnome-mount Now replaced by udisks? Here's my scenario. You can add a randome one with xfs_admin -U generate /dev/sda1 for btrfs: btrfs filesystem show uuid /dev/sda1 for JFS: it's in the output of jfs_tune -l /dev/sdc1.

with FUSE's userspace filesystems. There are few of those (apparently tmpwatcher was one) and most of those have been fixed, or have known workarounds. House of Santa Claus With the passing of Thai King Bhumibol, are there any customs/etiquette as a traveler I should be aware of? This worked for me...

On the other VM, we rebooted it, and the problem happened a half hour later. No Selective Self-test supported. The kernel exposes a relatively minimal set of syscalls, and libraries usually add to that, to make things like "open file by path" easier. Now sdc1 is my root partition.

fstab These are primarily notesIt won't be complete in any sense.It exists to contain fragments of useful information. If you had a boot menu there, tough luck. Keep in mind that the partition table is also in there. last night as I was moving data back onto the partition, this happened:Apr 6 21:48:16 localhost kernel: EXT3-fs error (device sdb1): ext3_lookup: unlinked inode 987759464 in dir #982532099Apr 6 21:48:16 localhost

Materials are provided for informational, personal or non-commercial use within your organization and are presented "AS IS" WITHOUT WARRANTY OF ANY KIND. If you want to find the difference, do a stat: st_size is the apparent size st_blocks*512 is the disk usage MBR backup and restore (Note: This does not apply to GPT The other partitions seem to be operating normally. In my case this problem was so annoying I was glad enough to be rid of it...

Current Customers and Partners Log in for full access Log In New to Red Hat? The last couple times this stuff wasn't there even though var is on a separate partition.Nov 4 02:23:23 alpha kernel: ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozenNov Additional mounts are placed somewhere inside that root filesystem, usually in recognizable places like /mnt/something, /media/something, sometimes /cdrom and/or /floppy, and such. Hooked up to the motherboard were two sata drives (sda and sdb).

Edit bug mail Other bug subscribers Subscribe someone else Bug attachments BootDmesg.txt (edit) Dependencies.txt (edit) Lspci.txt (edit) ProcCpuInfo.txt (edit) ProcInterrupts.txt (edit) ProcModules.txt (edit) Excerpt from syslog messages (edit) Add attachment • To do that, mount with mount -o barrier=1 and see whether you see any improvement. Not a security solution since binaries can be copied, but can be convenient. The current drives are WD Raptor 74GB 10k RPM drives (WDC WD740ADFD-00) and my experience with these is they die frequently.