frigidaire gallery stove f11 error Seneca Castle New York

Address 5 Park Pl, Phelps, NY 14532
Phone (315) 548-8045
Website Link

frigidaire gallery stove f11 error Seneca Castle, New York

Sounds like the EOC has gone bad again. I need some direction on where to look next. The clock turns on but will not allw me to adjust it and once again the broiler automatically turned on however this time the screen flassed the F11 error. But the beeping doesn't stop no matter what I do.Turns out that the problem is with the daughter control board that controls the warming drawer.

I hope this is helpful information. -Matt Feb 25, 2015 | Frigidaire Kitchen Ranges 1 Answer My stove won't stop beeping and has a FC error code - can I stop Gene. Jim // Dec 8, 2014 at 1:00 pm Hi Gene. To adjust the oven temperature higher 1.

If the reading is correct, the EOC would need to be replaced. Melde dich an, um unangemessene Inhalte zu melden. BUT oven not heating up. NOTE: OEC may initially display an F10 thinking a runaway condition exists.

See Details Frigidaire FFEW2425QB 24'' Single Electric ... The oven throws F30 regardless of whether the probe is attached. Very likely the problem is a faulty relay board. The controller does not see the motor rotating.  Press clear key.

The relay board turned out to be the problem, and our oven is back in action for taco night:) One more question for you though. Credentials confirmed by a Fortune 500 verification firm. Expert: Tyler Z. Sometimes while the oven is on but most of the time while the oven is cooling off.

Steve // Mar 29, 2015 at 8:13 pm Hi, I have a frigidaire oven Model #FES355EBA , I am getting the F10 error only when oven is on, does not error Wird verarbeitet... Dirk // Apr 25, 2015 at 4:10 pm Hi Gene, I have a Frigidaire electric range model FEF366DSA and the broil and oven elements are not working but the surface elements The correction for this problem is to replace the EOC.

Keep me posted. We have to... Your Own Question Tyler Z., Appliance Doc Category: Appliance Satisfied Customers: 73229 Experience: 9+ years being an appliance technician with factory training. 13574879 Type Your Appliance Question Here... Your answer needs to include more details to help people.

Most likely there is only one problem caused by the faulty EOC, but there is a very small chance for the latch motor to fail as well. Linda // Apr 19, 2015 at 8:26 am Model #PLES399ECF Hi, I am getting an F30 code and my oven will not work but my stove top does and the wirereading Do i have just 1 problem or 2 problems, i am not sure what i need to order. F11 just appeared one day without us using it, without a power failure, etc -is this common?

There is no a separate keypad in your range. Does she have solar panels on her house as we do? Powered by vBulletin Version 3.6.4Copyright ©2000 - 2016, Jelsoft Enterprises Ltd. Oven temp started to climb and would not shut off.

Here's the part you should of replaced. If fault returns when power is reconnected, continue the troubleshooting. As soon as I turn on the oven it started flashing the F30 error. Well, we followed your path, which was very helpful, but we have not solved our F11 problem.

The part number for the EOC is 316557205 The part number for the overlay is 316419303 Good luck and keep us posted. Judy // Mar 31, 2015 at 5:11 pm Hi Gene- Thank you so much for the time you put into helping folks with appliance issues! Ed Gene // Apr 23, 2015 at 9:29 pm Hello Ed, Thank you for your question. This error code means a shorted/faulty keypad.

Measure the resistance between the wires connected to these pins. So the EOC and clock/timer is the same part and looks like it would need to be replaced. Crystal // Mar 17, 2015 at 7:45 pm Hello, I have a Frigidaire Model#FGF337ABJ. Phone Numbers, Locate a Warranty Dealer/Service Manufacturers' Web Sites Measurement Conversion Chart Need to Complain?

There are four of them, one for each surface element. You may want to call customer service at 1-877-477-7278 to find out the ETA. Hopefully this information is helpful for you. -Matt Apr 23, 2015 | Frigidaire Kitchen Ranges 1 Answer The electric stove I have is beeping f11 how do I stop it from We then very carefully removed the silver covering on the control panel, uncovering the keypad base and we peeled back the flexible layer underneath the keypad.

it started to throw a f10 code after about 15min on bake and wont stop beeping until I unplug it..ive noticed the element will stay glowing red even when the oven If all situations above do not solve problem, replace EOC. Most likely the cause of the problem is a faulty relay. 2. Gene.

Just put in Kenmore range. Layer 1 is the printed keypad and layer 2 is the contact pad.You have to be careful in all this or you may crease or damage a panel. Check the temperature sensor resistance as described previously. Ken // Dec 25, 2014 at 7:12 am Hello Gene, Thank you for GLEFS77CSC is the model number I was able to clear the lock and the oven gave an F1

George sharon // Jan 1, 2015 at 10:09 pm i have a frigidaire model fgef301dnb. Follow 2 answers 2 Report Abuse Are you sure you want to delete this answer? Any suggestions would be appreciated. Turn off power for 30 seconds then turn power on.

I have a frigidare oven that the oven stopped working.the broiler is stll working fine.i called an appliance tech and he told me the eoc is bad so i orderd one