frigidaire error code f1 Schoharie New York

Make an Offer on all repairs We make deals

Address 836 E Main St, Cobleskill, NY 12043
Phone (518) 234-1679
Website Link

frigidaire error code f1 Schoharie, New York

The good part of this sad news is that you got nice opportunity for a good New Year (or may be it's not too late for Christmas?!) present to your wife Gene. Anmelden 7 Wird geladen... Otherwise the EOC is the culprit and would need to be replaced.

Older products will show only two digits F-codes, but on ranges manufactured beginning in 2004 many of EOC's will have expanded three digit fault codes. Ever had this problem? You can change this preference below. Note: If the new module does not have a faceplate, peel the faceplate from the old module and apply it to the new module in same position; do this before installing

Code f10. I have a Frigidaire model FFGF3047LSF. Remove the power to the range by turning off the corresponding circuit breakers prior to do any job. Replace oven temperature sensor (RTD) if wiring is ok.

I was wrong. The front left burner has quit working but only the center burner, not the outer two rings. The oven was working fine until in the last couple of days the PF code would come on after the oven had been on for a while. What should I do?

Please verify it. I have heard a few times what sounded like it shorting out from the control knobs on the right side. In such situation the only solution is to replace the EOC. When I replace the EOC again do you think I need to be concerned with the Molex connectors for the temp probes on both ovens?

Thanks in advance! Remove the oven door as instructed in the Owner Guide and inspect both hinges. Tried the coat hanger trick but couldn't feel the latch. Ask a Technician for Answers ASAP Ask an Expert Home Improvement Questions Appliance Repair How JustAnswer Works: Ask an Expert Experts are full of valuable knowledge and are ready to help

Thank you for your question. Anmelden 33 6 Dieses Video gefällt dir nicht? tom // Sep 2, 2015 at 11:48 am Gene, I have an Frigidaire electric wall oven model FEB27S6FCB which has given me an F10 error code. So that depends on your model.

You can use an universal flat oven igniter, made by GE. Frigidaire does not sell such harness but you can find a similar wires in a local electric or hardware store. Locate the two pins in the plug at the EOC that are connected to the sensor. You may want to check the igniter by measuring the current drawn by the igniter.

kimberly // Feb 26, 2015 at 6:22 pm Hi I have a frigidaire gas oven model LFGF3014LBC and have been getting f10 error for a while and now just started getting Phil // Jul 19, 2015 at 5:38 pm Hi Gene, We have a Frigidaire slide in stove/oven model no: CGES387AS5. About eHow Advertise Contact Us Write For eHow Terms of Use Privacy Policy Report Copyright Ad Choices en-US How to by Topic Mobile Privacy Connect with us Free Service - Appliance Check the upper oven temperature sensor by measuring resistance between two wires connected to the pin 9 and 10 at the plug P27.

As soon as the "locked" light comes on, push cancel. replied3 years ago. If it would not solve the problem, you always can return the part for full refund. I am lost as to how to proceed next as the touchpad was included with the new EOC?

Limit $10 in points per member. Gene. Just in case you will decide to get new control panel, the part number for the control panel is 316538405 Good luck. If the reading is incorrect, remove the sensor from the oven and check its resistance at the sensor.

steve // Dec 2, 2014 at 11:44 am hi gene PLEFMZ99ECC used to get f30 but now getting F7 12 and the front element wont turn off - any ideas ? Diese Funktion ist zurzeit nicht verfügbar. Gene. My questions: 1.

Judy // Mar 31, 2015 at 5:11 pm Hi Gene- Thank you so much for the time you put into helping folks with appliance issues! See the repair guide to fix it yourself Oven temperature sensor probe F3 Oven temperature sensor probe is shorted. It locked down and will not unlock again. Expert: Tyler Z. Thanks again and merry Christmas!

Unfortunately this part has been discontinued and is no longer available. If the error code returns, the EOC would need to be replaced. The part number for the EOC 316455410 Thank you for your question. Or should a person stay away from Electrolux?

It was 1 hr into baking and the temperature did runaway, everything was black. What is wrong with the oven temperature and what is the difference between the set and actual temperatures? If you would order the part from by clocking on the part number I posted, you have nothing to loose. Thank you for your question.

Thank you in advance!! Gene // Dec 21, 2014 at 12:39 pm Hello James, Unplug the range or turn off the range circuit breaker for a few minutes and reapply power. Most of the EOCs incorporated power relays among all other components while some of ovens use a separate power relay board to simplify design and lower cost of production. Replace the electronic control board.

I checked the resistance on the probe's bare wires and it reads 1099 ohms. Gene // Nov 21, 2013 at 3:17 pm Hello Dave. If any of the readings is incorrect (any resistance other than infinity), trace that wire and let me know where it goes to. Gene // Apr 1, 2015 at 8:35 pm Hello Steve, Thank you for your question.

Thanks. Clearing your browser history may delete your saved models.