fdisk error 16 linux Leonardsville New York

Address 205 Main St, Oneonta, NY 13820
Phone (607) 353-7192
Website Link http://www.pcprosolution.com
Hours

fdisk error 16 linux Leonardsville, New York

Link krishnadas.p.c July 22, 2012, 6:30 am It will be better if you add how to change the partition type too in this. Syncing disks. I then ran "hdparm -z /dev/sda" and this did the trick. Join our community today!

Size of the partition (or) the last cylinder number (Last cylinder, +cylinders or +size ). Read more about Ramesh Natarajan and the blog. Disk /dev/sdX is being used for system partition, for example for /boot and / (root). After the partition is created, format it using the mkfs command as shown below. # mkfs.ext3 /dev/sda7 5.

Click Here to receive this Complete Guide absolutely free. Are you new to LinuxQuestions.org? Reply Link Rakesh Gupta June 4, 2011, 4:37 amBLKRRPART failed: Device or resource busy Reply Link James Cassell September 11, 2008, 1:51 amThank You!You saved me from having to restart my Follow him on Twitter.

might be that it wasnt flushed to the device. You must get your raw devices listed in /proc/partitions before you can do a scandisk. WARNING: Re-reading the partition table failed with error 16: Device or resource busy. Also, the partition is empty, right?

When you want to disable or enable the boot flag on the corresponding partition, do the following. This site is not affiliated with Linus Torvalds or The Open Group in any way. The new table will be used at the next reboot or after you run partprobe(:cool: or kpartx(:cool: Syncing disks. There is nothing wrong with that, but this is larger than 1024, and could in certain setups cause problems with: 1) software that runs at boot time (e.g., old versions of

The kernel won't reread a partition table unless the device isn't in use... –derobert Mar 3 '14 at 16:49 Does partprobe help? –Gilles Mar 3 '14 at 21:33 add This is the result of the whole operation... it is telling him to either reboot or run partprobe... If rebooting and the USB2 drive still has issues, check hdparm config.

after reboot only it will working Link Vigneshwaran March 2, 2015, 1:50 pm Ramesh, Article was really good!!! Command (m for help): w The partition table has been altered! But, the system might've created the new partition as sda7. i have installed GParted but it is returning a strange type of error.

Type "sudo mkfs.ntfs -f /dev/sda2" to turn /dev/sda2 into an NTFS partition. If you do not receive this warning when you do this on your own then you should have nothing to worry about. Jerry srs5694March 28th, 2010, 06:08 PMAll I am going on is fdisk's error message... HOW SCANNING HAPPENS The scan proceeds in four basic stages.

So gist of the story if you don't have parted 3.1 in your system be ready to reboot your system. It's fixed. share|improve this answer answered Sep 11 '15 at 20:47 Ciro Santilli 烏坎事件2016六四事件 法轮功 1,1511217 add a comment| Your Answer draft saved draft discarded Sign up or log in Sign up Contact Us Email Me : Use this Contact Form to get in touch me with your comments, questions or suggestions about this site.

We Acted. There is nothing wrong with that, but this is larger than 1024, and could in certain setups cause problems with: 1) software that runs at boot time (e.g., old versions of If you need to reset your password, click here. It's very important to, among other things, ensure that you're editing the proper block device.

reboot;" it tells him that the "...new table will be used at the next reboot...". partition fdisk linux share|improve this question edited Jul 7 '09 at 12:49 asked Jul 5 '09 at 12:10 Teddy 3,63311224 add a comment| 10 Answers 10 active oldest votes up vote Enter the partition number and a type code of "07" when prompted. Calling ioctl() to re-read partition table.

Our Heroic Support Team is available 24 hours by phone or e-mail to help. so something has changed. Subscribe to the Knowledge Base SubscribeSubscribe X Javascript not enabled - Portions of this site require javascript to work. Or should it be fine only with a reboot ?

Why are so many metros underground? onebuck View Public Profile View LQ Blog View Review Entries View HCL Entries View LQ Wiki Contributions Find More Posts by onebuck View Blog 06-22-2009, 01:41 AM #3 ytd Member jawilljrMarch 28th, 2010, 12:44 AMThis is the result of the whole operation... All rights reserved | Terms of Service ≡ MenuHomeHowtos and TutorialsLinux Shell Scripting TutoriaLAboutRSS/FeednixCraftLinux Tips, Hacks, Tutorials, And Ideas In Blog FormatRe-read The Partition Table Without Rebooting Linux System by Vivek

Reply Link DaveQB May 24, 2011, 2:56 amI found that even after all the fdisk'ing, the partition/disk was still in use. Had to reboot servers. Let's take a look at the partition configuration so far.