fax receive error codes Lake Luzerne New York

Address Glens Falls, NY 12801
Phone (518) 832-6708
Website Link https://www.techquest.guru
Hours

fax receive error codes Lake Luzerne, New York

Cause: Abnormal protocol. Cause: Usually--cannot receive picture signals properly due to poor line conditions. Cause: When the power is turned on after or when the BJ cartridge is installed, there is a foreign material in the carriage unit. Press the [Pause/Redial] key after, for example, the area code.

Support Forum Join the conversation! Make sure the remote machine can accept and use polling. Error Code(s) Definitions/Causes Solutions 386 387 388 389 390 391 392 393 394 395 There is too much noise on the line for a valid connection between two fax machines to Solution: Record the protocol on DAT tape and then request the Canon Technical center to analyze the information. ##290 [ TX ] Receive signals other than PIN, PIP, MCF, RTP

A. Cause: SCNT PWB malfunction. Solution: Contact the telephone company and request maintenance. ##203 [TX / RX] Operational error due to causes other than codes #003 thru #008 A. Cause: The caller disconnected the line or unable to detect the signal from the caller.

Retry the fax reception when line conditions might have improved. If toner or print paper is empty, supply them. A. Solution: Replace the modem or modem attached circuit board.

B. A failure on "telephony error" does not necessarily mean that your fax will never be successfully transmitted. Solution: Have the other party lower the reception level to prevent the other party from receiving echo signals. ##103 [ RX ] Fail to detect EOL for 5 seconds (15 Solution: Record the protocol on DAT tape and then request the Canon Technical center to analyze the information. ##289 [ TX ] Receive signals other than PIN, PIP, MCF, RTP

Ask the sender to set the document.T60Register the document that is sent to the recipient by polling.T61Check whether the document to be sent by polling from the bulletin board is registered.T62Inform Cause: Defective internal unit; (+24 volts down). The remote (calling) fax machine determined that there was a feature incompatibility between the two machines. You may be able to get around it by reconfiguring your HP fax to receive at a slower speed. 200 Code - In this case, your fax session has timed out.

Solution: Have the other party boost the transmission level to receive picture signals properly. A. Cause: The other party cannot receive. Cause: The length of 1 document is longer than 2 A4 size sheets.

C. Send to another fax machine to make sure the issue is with the one specific remote machine. 380 ECM The remote machine failed to issue a valid response to a CTC See the solutions provided for errors 2XXX32 to 2XXX84 in the above table. Solution: Replace the read end sensor. ##503 [ TX ] Fail MCF1 or PIS reception during G1 transmission.

Cause: Carriage motor does not work. Solution: Lower the transmission level to prevent echo reception of transmitted CFR. ##115 [ TX ] Exceeded the one-line maximum transmission time (5 seconds) during picture transmission. Cause: Defective internal unit. Solution: Replace the SCNT PWB. ##100 [ TX ] Excessive repeat protocol during transmission.

Adjust the image density. Solution: Boost the transmission level so that the other party can receive the signals immediately before GC2, PIS or the Phase signals. Solution: Boost the transmission level so the other party can receive TCF properly. A.

Solution: Check to see if the length of the document transmitted in fine and standard mode exceeds 630 mm and 420 mm respectively. Solution: Boost the transmission level so the other party can receive picture or MPS signals properly. Cause: SCNT PWB malfunction. Solution: Replace the Thermal head.

Cause: Abnormal protocol. Solution: Refer to Service manual ##322 [ RX ] Printer (LBP) Fixing unit trouble. A. Cause: Abnormal protocol.

Failed Hangup: No loop current. (3) This means that once we dialed the number we got dead air, no ring tone and no answer. Cause: The Thermistor is defective. D. Solution: Lengthen the no-sound time after receiving CFR so the other party can receive picture signals properly. ##284 [ TX ] DCN reception after TCF transmission.

A. Cause: Printer control EEPROM is damaged. Solution: Perform echo counter-measures as listed in Service manual. This may be due to a call clarity issue.

If the document is large, ask the remote user to re-send the document as two or more smaller documents. Cause: Other party experienced echo malfunction. A. Cause: Defective internal unit.

Solution: Have the other party boost the transmission level to receive picture signals properly. ##612 [ RX ] Fail to detect picture signals for 5 seconds after CFR transmission during There was an error while generating the document. Cause: The home position sensor stays ON or OFF. Configure the remote machine for poll transmission.

Call the telephone provider if line conditions fail to improve. Although there are many HP fax error codes, most people only encounter a small handful of them. We suggest your test the number by calling it from a land line to see if you can get through or change the fax number. Solution: Have the other party boost their transmission level to allow for proper phase signal reception.

Cause: The other party cannot receive the signals properly due to low transmission level. Cause: (Q signal transmission after picture signals); The other party cannot receive picture or Q signals properly due to poor line conditions. If you have an error code when sending a fax with your HP machine, there is one easy way to remedy the situation: Disable V.34, which is also known as the