fax error Lake Placid New York

Address 1936 Saranac Ave, Lake Placid, NY 12946
Phone (518) 523-5959
Website Link http://www.foreverwild.com
Hours

fax error Lake Placid, New York

Ask your administrator to set the SMTP server address. B. Cause: STOC (F-network side) detected abnormality. Solution: Adjust the NL equalizer so the picture signals can be received properly.

The remote (calling) fax machine determined that there was a feature incompatibility between the two machines. Solution: Replace the read end sensor. 2. Cause: The other party experienced echo malfunction. C.

Solution: Lower the transmission level to prevent echo reception. ##202 [TX / RX] Fail to detect the last binary signal from the other party. Error Code(s) Definitions/Causes Solutions 386 387 388 389 390 391 392 393 394 395 There is too much noise on the line for a valid connection between two fax machines to Cause: Printer control ROM malfunction Solution: Power cycle the machine. Solution: Divide the job so that less than 31 document are sent at one time.

Print This PagePrint ShareShare Url of this page: HTML Link: Bookmark Manuals Brands Toshiba Manuals All in One Printer E-STUDIO 555 Troubleshooting manual Toshiba E-STUDIO 555 Troubleshooting Manual: Error Codes On Solution: Boost the transmission level so the other party can receive EOM or PIS signal properly. Cause: The ink sensor is defective. Solution: Replace the BJ printer control ROM.

A. Cause: Thermal head trouble. A. The remote machine automatically ended the call immediately before, or just as the local machine answered the call.

Turn the power OFF and then back ON. A. Solution: Replace the password memory attached unit. ##554 [ TX / RX ] Abnormal password input via other party's line. Set Fax Speed to slowChanging those settings seems to resolve a lot of faxing issues, but if after trying those steps you continue get that error code or even another one,

Support System Home Solutions Forums Return to Website How can we help you today? Ask the sender to set the document.T60Register the document that is sent to the recipient by polling.T61Check whether the document to be sent by polling from the bulletin board is registered.T62Inform Cause: Bi-directional print displacement correction failed because the carriage motor is out of step, or some similar reason Solution: Replace the trailer unit and carriage unit. ##339 [ RX A.

Cause: Other party cannot properly receive phase signal due to poor line conditions. This prevented the fax from receiving any more pages, and caused it to terminate the session prematurely. Solution: Contact by phone. Cause: The ink detection sensor is faulty Solution: Replace the ink detection sensor Solution: Replace the unit containing the ink detection sensor. ##349 [ TX ] Home position

Solution: Set the document and have the other party call again F. Solution: Replace the SCNT PWB, and register a value for the absorption capacity, according to the quantity of absorbed ink in pad. ##342 [ TX / RX ] Cleaning absorption A. Wait several minutes between the end of one transmission and the start of the next transmission. 383 ECM Disable ECM, and then try faxing again.

A. Solution: Have the other party lower the transmission start speed to 4800 bps. H. D.

A. Disable ECM, and then try to receive the fax again. A. A.

Cause: Other party experienced echo malfunction. Configure the remote machine for poll transmission. Cause: (After TCF transmission before picture signals); The other party cannot properly receive due to low transmission level. Solution: Refer to Service Manual. ##302 [ TX ] Interface error between reader and controller.

Spaces Browse Pages Blog Labels Space Operations Quick Search Help Online Help Keyboard Shortcuts Feed Builder What’s new Available Gadgets About Confluence Log In SEARCH WIKI Tools Attachments (0) Page Cause: Trouble with image storage memory Solution: Replace the circuit PWB (SCNT, etc.) Mounted for transmission memory ##220 [ TX / RX ] System error (main program runaway). Solution: Turn the power OFF and then back ON ##227 [ RX ] Attempt to record file without picture data. B.

B. Cause: BJ cartridge (BJ head) malfunction. Contact the destination; the number may be a Voice/Fax number and needs to be switched to fax to receive your transmission. Reset the maintenance jet absorption pad capacity to 0, in the service mode.

A. Solution: Have the other party boost their transmission level so they can receive picture signals or EOM properly. A. D.

Check the ink capacity of the ink suction unit waste ink tank, and input the waste ink capacity value corresponding to the amount of absorbed ink. Cause: Other party cannot receive signal properly due to poor line conditions. Solution: If the other party is not a Canon model then contact them and have them set all passwords to [1]. Solution: Print out all the data, clear the memory and then re-register data.