fax error invalid remote width Lake Katrine New York

Address 1681 Platte Clove Rd, Elka Park, NY 12427
Phone (518) 734-5477
Website Link http://mtcshop.com
Hours

fax error invalid remote width Lake Katrine, New York

Unspecified phase D error Communication error occurred Communication error, usually because the fax hardware is incompatible, often caused by outdated hardware. Received other than DIS while waiting for DIS The fax service expected to receive the remote fax machine's fax capabilities, but received an unexpected message instead. Logged John GageSystems AdminKnight Crockett Miller Insurance Group - Toledo, OH4 locations in Ohio and Indiana53 users TAM Online Nick Oliver Frequent Flyer Posts: 128 Karma: +46/-2 Re: Frequent 'Invalid Width' Please don't fill out this field.

TRM_B_NO_LOOP_CURRENT - No loop current detected TRM_B_LOCAL_IN_USE - Local phone in use TRM_B_CALL_COLLISION - Ringing detected during dialing TRM_B_CONFIRM - Confirmation tone TRM_B_DIALTON - The No line is detected which could be a problem with the line, switch, or card. 332FCP_CNGDETCTCNG fax calling tone detected. 333FCP_RMTOFFHKRemote fax machine went off-hook (also known as Answer Supervision). 339FCP_ANSWER_TONE_DETECTFax Try Resending the fax. 348FCP_ISDN_CALL_PROGRESSBy enabling call progress on an ISDN D channel, one of the following values will be in the second byte of the FIFO buffer: 4: CALL_PROCEEDING: Call DCE to DTE data underflow Communication error occurred Communication error, usually because the fax hardware is incompatible, often caused by outdated hardware.

Log entry lost The call started, but the log entry for the call was lost / incomplete. Generated Sat, 15 Oct 2016 17:51:42 GMT by s_wx1131 (squid/3.5.20) E117 : COMREC invalid response to repeated PPR received E118 : T.30 T2 timeout, expected signal not received E119 : COMREC invalid partial-page signal received E120 : Cannot synchronize ECM frame By default, if a value has been specified for this setting, then ExtraFax's Pre-TransmissionProcessing agent will copy that value to the AppCallerID field of the outgoing fax job, which controls the

TRM_B_INCMP_FTM - Binary File Transfer mode specified, but not supported by receiver. Unspecified image format The image format to be transmitted was not specified Image conversion error Error converting the specified image into a faxable format Use a different image format for This could be due to there being no fax machine on the receiving end, or a lack of call clarity. This could be due to there being no fax machine on the receiving end, or a lack of call clarity.

DCE to DTE data overflow Communication error occurred Communication error, usually because the fax hardware is incompatible, often caused by outdated hardware. Related Support FAQ... 327FCP_SITINTCIntercept tone detected; remote end originating failure; invalid telephone number or class of service restriction. Depending on the remote machine's behaviour, it may have still printed the sent page and any preceding pages. Try dialing the number from another phone to verify the number is a fax number. 318FCP_DIALTONDial tone detected; usually indicates the dialing sequence did not break dial tone.

TRM_B_NOCONT_NSTMSG - Do not continue with next message after receiving ERR. No response after sending a page The remote fax machine did not acknowledge that a page of the fax was received. Fax transmission not established We could not detect a remote fax machine. Invalid ECM response received from receiver The fax service received an invalid error correction message from the remote fax machine.

Far end cannot receive at the resolution of the image The remote fax machine does not support receiving faxes sent at the resolution that our service sends at. The Central Office connected to the dialed number generates this signal. No Dial tone No Dial Tone on the phone line Check that the line is connected to your fax hardware and that it is operational. TRM_B_RCVB_INVAL_DMACNT - Invalid DMA count specified for receiver.

Invalid response after sending a page An unexpected message was received after successfully sending a page. Try dialing the number from another phone to verify the number is a fax number. 305FCP_CONFIRMConfirmation tone; automated equipment acknowledges successful completion of caller requested feature (for example, call forwarding). Used instead of BUSY1 in certain countries. The fax does but the other device is rarely used.

This occurs when you did not access an outside line. No response to EOM Communication error occurred Communication error, usually because the fax hardware is incompatible, often caused by outdated hardware. E427 : Remote does not support JPEG fax resolution. If JavaScript is disabled in your browser, please turn it back on then reload this page.

Received a DCN from remote after sending a page The remote fax machine responded with a disconnect message after a page was sent successfully. E428 : JPEG fax requires square resolutions. Remote cannot receive The receiving end cannot receive faxes Make sure the receiving end has a fax device up and running Invalid remote ECM mode The receiving end incorrectly reported support This indicates there is a problem with the line, switch, or card.

In fax mode, this result occurs after the ced_timeout (default: 40 secs) has expired and the line continues to ring (You can adjust the value of these timeout parameters in the Keep in mind SimplyCast only charges for successfully delivered pages, and will remove any number that has been determined permanently unreachable. TRM_B_RCVB_FTM_NOECM - Binary File Transfer specified, but ECM not supported by receiver. Possible bad number.

Try dialing the number from another phone to verify the number. 308FCP_RING1Ringback detected; remote end is ringing. Invalid response to EOM Communication error occurred Communication error, usually because the fax hardware is incompatible, often caused by outdated hardware. E424 : Modem does not support JPEG fax request. The system returned: (22) Invalid argument The remote host or network may be down.

When a bulk fax is sent unsuccessfully the receiving machine provides an error message output to let the bulk Fax Service understand the reason for failure.