f 51 error code cabrio washer Fairport New York

Address 1 S Clinton Ave Ste 800, Rochester, NY 14604
Phone (585) 359-2922
Website Link http://5linx.com
Hours

f 51 error code cabrio washer Fairport, New York

If resistance readings are tens of ohms outside of range, replace the entire log valve assembly. by Manage My Life December 31st, 2012 Comment -1 votes Didn't find what you are looking for? It was the bolt that holds the rotor, it was loose. Appliance Repair (whirlpool Cabrio OL/UL Code) - Dauer: 4:20 DC Appliance Repair 17.308 Aufrufe 4:20 Whirlpool Cabrio Kenmore Oasis Bearing Repair Part 1 (New) - Dauer: 9:38 RenewAppliance 271.517 Aufrufe 9:38

my wife also found on this machine that her start buttom was broken sounds like another common problem. After removing the rotor, I could tell everything was fine. If the mini-cycle is unsuccessful, uL will flash until the door lid is opened, allowing the customer to view and redistribute the load. Thanks, resolved the problem, found a shirt between the drum and the tub.

Yes No Cancel Update (+2 points) 16 more comments Anonymous Jan 09, 2008 my error is flashing AF on the dryer. Motor Thermistor 15.1K at 66 degrees F. You can change this preference below. With an ohmmeter, check for continuity between the neutral (N) terminal of the plug and P13-1 on the machine/motor control.

Your question was published, help is on its way! Plus labor if you don't want to do it yourself. (Here is a video on how to replace these: http://youtu.be/L0p1VGSTzdU Source: Repair Clinic. Got the f51 code a few days ago. Check hose connection between the pressure transducer on the machine/motor control and the pressure dome attached to the tub.

Perform Manual: Door Switch and Manual: Door Lid Lock tests. 2. But she says it doesn't clean clothes very well, which is her excuse for using more than the proper amount of detergent, which the repairman says is ******* the machine because I have had a sock and 2 hand towels rolled up really tight that wedged between the top of the tub and the side. Reply With Quote September 29th, 2013,11:09 PM #8 rickgburton View Profile View Forum Posts Appliance Tech - Moderator Join Date Jul 2006 Location Murray, Utah 84107, United States Posts 24,364 I

The self diagnotic mode would fail at C8 but everything tested okay when I did the manual diagnostic test. Mine has completely stopped working at this point, as trying to finish the load left me to no alternative but to try the drain n spin and rinse n spin options Tightened it with an allen wrench and the machine ran with no more errors. With an ohmmeter, check for 16 ohms resistance at the P5 connector between pins P5-1 and P5-2, and also between pins P5-1 and P5-3.

When the technician was here, he said we might need replacement of the wiring harness which is part of the rotary position sensor. To my suprise, there was no hair in the bottom of the tub. With an ohmmeter, check for continuity between all pins on the P10 machine/motor control connector and the motor rotor position sensor (RPS) connector. Is the manual test just a test to see if it will spin properly or is it a test to fix the issue?

Second, as long as Whirlpool continues to do this, make certain that every Cabrio owner knows of the problem before paying for repairs. Thank You very Much! However, I will add a warning. We are glad to hear that you found the cause of that problem and that it was simple to fix.

Thanks, great advice Peter Newell Jan 09, 2015 This worked for me as well. Disconnect connector P1 and P2 from the machine/motor control.See Figure 4, page 6-16. Anonymous Dec 29, 2008 I bought my Cabrio washer (WTW6600SG) just 2 years ago. comparing the plug to the wiring diagram and wire colors, I was able to figure out which connector is which on the board.

June 27, 2010 at 12:49 AM Casey said... Hinzufügen Möchtest du dieses Video später noch einmal ansehen? See TEST #3. And to all with this same problem, Call them!!! 866-698-2538 Posted on Mar 27, 2010 Helpful 5 Not Helpful Comment Flag You can't post conmments that contain an email address. ×

Posted on Feb 23, 2010 Helpful 1 Not Helpful Comment Flag You can't post conmments that contain an email address. × Comment Anonymously Video Images Anonymous Re: whirlpool cabrio error code Top Load Washer - White See Details Kenmore 27132 4.8 cu. http://m.youtube.com/#/watch?v=L0p1VGSTzdU&desktop_uri=%2Fwatch%3Fv%3DL0p1VGSTzdUHere is a YouTube link on control board replacement:http://m.youtube.com/#/watch?v=BxXuJ7y1pBg&desktop_uri=%2Fwatch%3Fv%3DBxXuJ7y1pBgLooks easy enough. If visual check passes, replace the user interface assembly. 2.

Contributor 1 Answer Re: whirlpool cabrio error code f51 what does it mean? If there is continuity, replace the drive motor. I researched the code on several sites. Perform steps in Accessing & Removing the Electronic Assemblies, and visually check that the P5 connector is inserted all the way into the machine/motor control.

This requires removing inner basket to remove stuck clothes. Technician out again. If basket does not turn freely, determine what is causing the mechanical friction or lock up. 4. the quite above is from the PDF manual.

I called them too and YES IT'S TRUE! If you get no codes after the self diagnosis test then you should be good to go at no cost! so I took your advise. Benton Harbor Michigan 49022 January 14, 2013 at 6:05 PM WPK Tech said...

but my question is has anyone had this one problem fixed and it completely solved it or have they kept having problems with the machine....im pondering getting it fixed selling it Cabrio Top ... Unplug and then plug the wiring harness connections back in on these components 5 or 6 times. Is the pump running?

Contributor 2 Answers Re: whirlpool cabrio error code f51 what does it mean? Problem Solver: An expert who has answered 5 questions. Here are some Whirlpool numbers to call: Recall Department: 1-800-253-1301 Customer Service: 1-866-698-2538 Thanks and good luck! I called the local non-chain appliance store where she had purchased it for advice.