ford computer error codes Pinos Altos New Mexico

Address Silver City, NM 88061
Phone (575) 313-0218
Website Link
Hours

ford computer error codes Pinos Altos, New Mexico

Electronic Engine Control (EEC / PCM) processor Keep Alive Memory (KAM) test failed ========================================================== 18 Injected 1. P1670 EF signal not detected Open/shorted EF circuit P1690 Waste gate failure WGC circuit or solenoid, PCM P1702 TRS sensor intermittent circuit malfunction Sensor, wiring, PCM, mechanical alignment P1704 Digital TRS Turn ignition "OFF". Parts or components should not be replaced with reference to only a DTC.

Grounded circuit P0560 System voltage malfunction Charging system problem/load, glow plugs still enabled P0562 System voltage low Low sys. No Heated Oxygen Sensor (HO2S) switching detected (front - HO2S) ========================================================== 92 Injected Heated Oxygen Sensor (HO2S) sensor indicates system rich (front - HO2S) ========================================================== 95 Injected Fuel pump secondary circuit If you have any doubt as to repairs on your vehicle, please contact a qualified technician. Intake Manifold Runner Control fault P1530 Open or Short to A/C Compressor Clutch circuit P1537 Intake Manifold Runner Control Stuck Open P1538 Intake Manifold Runner Control Stuck Open P1539 Power to

On 87–90 models, a base readout of 4030 indicates engine running self test has been entered. Start engine and bring to normal operating temperature. Ford Trouble Codes 88-95 1.3L EFI, 1.6L, 1.8L, 2.0L w/4EAT & 2.5L 93-95 probe 93-95 EEC Villager 96-97 1.3L EFI, 1.8L & 2.5L 96-01 OBD2/MIL EEC 1.3L FBC Engine exc. sensor circuit high input Open circuit, biased sensor, PCM, short to 5v P0122 Accelerator pedal sensor circuit low input Grounded circuit, biased sensor, PCM P0123 Accelerator pedal sensor circuit high input

Exhaust back pressure high / Pressure Feedfback (PFE) circuit voltage high ========================================================== 35 Injected Pressure Feedfback (PFE) circuit above maximum voltage ========================================================== 41 Injected 1. Ford DTC's (Diagnostic Trouble Codes)Data Link Connector (DLC)(Located Under hood)Analog Voltmeter Connection Ford 11 System PASS. 12 Cannot control rpm during KOER Sell-Test high rpm check. 13 Cannot control rpm during malfunction Open/grounded circuit, sensor fault, short to power P0341 Camshaft position sensor ckt. Well, look no further.

Record DTCs by reading MIL flashes. For example, a dirty MAF sensor might be causing the car to overcompensate in its fuel-trim adjustments. Electronic Engine Control (EEC / PCM) processor ROM test failure 2. Continous Memory Codes KOEO codes are separated from Continuous Memory codes by a 6-second delay, a 1/2-second sweep (separator) and another 6-second delay.

On 87–90 models, DTC output will be the RH three digits displayed. The vehicle service manual should be consulted for more information on possible causes of the fault, along with required testing. This site is neither authorized by, nor affiliated with, Ford Motor Company. To conduct Key-ON/Engine-OFF (KOEO) Self test portion, hold in all three buttons and turn ignition On, then release three buttons.

Code type Explanation Generic (normally P0xxx) The definition for the code is defined in the EOBD / OBD-II standard and will be the same for all manufacturers. Power Steering Pressure Switch (PSPS) circuit did not change states ========================================================== 53 Injected Throttle Position sensor (TPS) circuit above maximum voltage ========================================================== 54 Injected Air Charge Temperature sensor (IAT) indicates -40°F COPYRIGHT © 2007 - 2016 WWW.SUPERDUTYPSD.COM, ALL RIGHTS RESERVED Contact | Privacy Policy Autozone is one place that will give you the code number.

Electronic Vacuum Regulator Control circuit fault P1410 EGR Barometric Pressure Sensor VREF Voltage P1411 Secondary Air is not being diverted P1413 Secondary Air Injection System Monitor circuit Low Voltage P1414 Secondary c. sensor ckt. malf.

Or do it yourself with the procedure posted below. Accessing DTCs. on 29 January 2013 07:25 PM What is a Diagnostic Trouble Code (DTC)? A single digit number of three will be reported by three flashes.

All information on this site is copyright protected. Merkur 2.9L & 85–88 2.3L Engine 1. Using Message Center Continental Using electronic instrument cluster, hold in all three buttons (select, checkout and reset buttons) at same time. Using Check Engine/ MIL Exc DI 7.3L Turbo Diesel, Merkur (2.9L), Villager & 85–88 2.3L Engine The MIL lamp is intended to alert the driver of certain malfunctions in the engine

Power Steering Pressure Switch (PSPS) circuit is open 2. Intake Manifold Runner Control Stuck Open P1520? We do ask that you please read the info available on the site first so that we can help reduce repeat questions. fluid temp.

Which will dig a lot deeper into your car's performance, health, chip data. Turn the ignition on. 3. Villager EEC-IV EEC-IV/OBD2 EEC-V EEC-V/OBD2 MCU MCU 7.3L Turbo Diesel (R) = Engine Running test (M) = Memory code  (O)=Key On Engine Off test   2 Digit Codes 11 System OK 12 Aspire, Capri (1.6L), Escort & Tracer (1.8L), Probe (2.0L w/4EAT, 2.2L & 2.5L) & 88–93 Festiva 1.

They will provide valuable info! Disconnect battery ground cable, DTCs will be erased from back-up memory after 24 hours. Refer to our Generic OBD II code list for definitions on all other Ford diagnostic trouble codes.Manufacturer Specific Codes P1000 OBD System Readiness Test Not Complete P1001 KOER Test Cannot Be Intake Manifold Runner Control fault - Stuck Closed P1520?

Remember, these are manufacturer specific codes only. Message center See Image above On 87–90 models, a base readout of 4255 indicates that KOEO self test has been entered. Some shops will scan your codes for free. Difference Between Generic & Manufacturer Specific...

Remove jumper wire and reconnect DTC. When retrieving Ford check engine light codes with an OBD II scan tool, proceed as follows: 1. Remove jumper wire from self test input terminal as soon as first diagnostic trouble code is received (even if an 11 is the first DTC). 3.