frigidaire f31 error South Dennis New Jersey

Custom Built Computers, Repairs/Upgrades, Installations, Virus/Spyware removal.

Address 321 Shore Rd, Somers Point, NJ 08244
Phone (609) 816-0470
Website Link
Hours

frigidaire f31 error South Dennis, New Jersey

I have spent lots of time researching my issue and can not find anyone else describing this particular problem. Gene. If the lock motor, switches and wiring are good, the EOC would need to be replaced. All-Star: An expert that got 10 achievements.

Jim // Dec 8, 2014 at 1:00 pm Hi Gene. George sharon // Jan 1, 2015 at 10:09 pm i have a frigidaire model fgef301dnb. does this fall with in the range of working resistance? The part number is WB2X9998 Good luck and keep us posted.

I checked the other plastic connector (from the EOC side) and received above 1650 ohms. If it would not solve the problem, you always can return the part for full refund. Could you please explain what this is. If the sensor measures less than 500 ohms, it will need to be replaced.

I pulled it off, are you sure you're referring to the correct model? If the sensor and wiring are good, replace the EOC. I am unsure how to check every individual wire in the harness (if that is the suggested next step). I do not think they will keep it available for more than five years since production started.

So the only solution is to replace the EOC. Unplug from the EOC the black wire connected to the L1 terminal and insulate it using an electric insulation tape. If the reading is correct, test operation of the potentiometer by measuring the resistance between pin terminal G (center) and either of the outside pin terminals as the control shaft is Pull it out of the wall and remove the control panel rear cover.

Bad EEPROM Identification/Checksum error. 1. (F10 only) Check *RTD Sensor Probe & replace if necessary. I can't help but worry there is a bigger issue, this time this was NOT relatively close to a self clean, which I have read can be a cause of electrical F13 Control's internal checksum may have become corrupted.  Press clear key. What was wrong at that time?

Contact the seller and request the replacement. Gene. Gene. If the reading is incorrect, the temperature probe (sensor) would need to be replaced.

Check wiring of lock motor, lock switch and door switch circuits. Gene // Dec 28, 2014 at 2:41 pm Hello Ken, The only way you can do it is to disconnect the EOC. Older products will show only two digits F-codes, but on ranges manufactured beginning in 2004 many of EOC's will have expanded three digit fault codes. NOTE: You should only access and check internal range components if you are completely confident in your technical ability to safely perform the process.

F8, F9 or F90 - Lock motor switches improperly positioned. Also, if it would not and you ordered the part from AppliancePArtsPros.com, you can return it within 365 days. The controller does not see the motor rotating.  Press clear key. I have an Electrolux model#EW30DF65GSB.

Get more answers from the people in your networks Tags Frigidaire , Ranges , Wall Ovens , Appliances Click to remove this tagging. Get the Manual Here Chris posted an answer 2 years, 11 months ago 0 Hello lmundy, thank you for allowing me to assist you! Both probes check 1178-1179 OHMS at the probe and the board. and 2 other Appliance Specialists are ready to help you Ask your own question now Share this conversation Related Appliance Questions Question Date Submitted My Maytag fridge is not cooling, part

If the oven will continue to heat, the oven relay board would need to replaced. F31 Shorted sensor probe or wiring problem. If the fault returns, replace the keyboard ( membrane ). Dirk // Apr 25, 2015 at 4:10 pm Hi Gene, I have a Frigidaire electric range model FEF366DSA and the broil and oven elements are not working but the surface elements

The part number for the porcelain wire nuts (pack of 10) AP3440631 Good luck. Thanks again for all your time and help!! Rave Reviews "I thought it was the best online shopping experience that I have ever had when it comes to parts." Eric H. Internal metal edges in the range can be sharp.

Linda // Apr 19, 2015 at 8:26 am Model #PLES399ECF Hi, I am getting an F30 code and my oven will not work but my stove top does and the wirereading You can determine it by visual EOC inspection and/or by the wiring diagram for your oven (if it is available). Appreciate any help! Otherwise the relay board is the culprit.

I have replaced the EOC and the RTD, and still get the error code, what else could it be :(? Keep me posted. Unplug P1 connectors from both of the power supply boards and restore the power to the range. F-10 Error Code.

Nov 21, 2012 | Kitchen Ranges 1 Answer I have a Crosley oven and I'm getting a beeping sounds and error message F31 and I cannot find my manual How can Locate the P5 connector at the EOC and remove two violet wires from pins 12 and 13. To adjust the oven temperature higher 1. See Details Frigidaire FPMC2785PF Professional 3.8 cu.

Thank you, Gene. I have seen many articles online about those connectors not being very good. What do I do nezt Gene // Apr 23, 2015 at 10:30 pm Hello Linda, Sorry for the delay. O.o Nov 13, 2011 | Crosley Kitchen Ranges 1 Answer When I try to turn on oven the code F31 shows Hi and welcome to FixYa, I am Kelly See this

With the diagnostics above, I was able to pretty quickly determine that the EOC was bad. What does F31 error code indicate on a Frigidaire gas range? Report This by Manage My Life December 20th, 2008 We had oven temperature problems and had technician come out and Shop HalloweenCostumes.com for Suicide Squad costumes and accessories. The clock turns on but will not allw me to adjust it and once again the broiler automatically turned on however this time the screen flassed the F11 error.

Thank you for helping an elderly veteran with this vexing problem. These ovens have very badly stamped metal inside that will cut through wiring very easily. characters left:

Contact Us|Terms of Service|Privacy & Security|About Us|Our Network|Sitemap © 2003-2016 JustAnswer LLC JustAnswer UKJustAnswer GermanyJustAnswer SpanishJustAnswer Japan 51 11912553 Go Automotive Baby Care Car Audio & Video Cell Phone Communications Computer Good luck.