fanuc p type spindle amplifier error code Helmetta New Jersey

Address 2681 Quakerbridge Rd # 82, Trenton, NJ 08619
Phone (609) 689-0030
Website Link
Hours

fanuc p type spindle amplifier error code Helmetta, New Jersey

Alarm 13 (AL-13) CPU Inter Data Memory Alarm Replace PCB Alarm 14 (AL-14) ROM Is Defective Cause ROM not mounted, not mounted correctly or fault Remedy Check EPROM. In such a case, the motor is not activated. Check the parameter settings. Before specifying absolute position commands in succession, perform absolute position command orientation.

Are you sure you want to continue?CANCELOKWe've moved you to where you read on your other device.Get the full title to continueGet the full title to continue reading from where you However, a value other than 128 /rev is set. Check the parameter settings. Remedy Check AC power, replace damaged fanuc part.

We have undertaken various repairs, From simple jobs like Fanuc Servo Drive's that required a quick change of a blown transistor which then was retested on our closed loop Fanuc Test Remedy Replace parts, replace fuse. SPINDLE DRIVE PART NUMBERS, SPECIFICATIONS AND PCB PART NUMBERS Alpha Series Spindle Amplifier Modules (SPM) Type 1 New Specifications (Supporting Spindle HRV Control) CE Marked Products Model Drive type Main PCB ER-14 SFR (normal rotation command) and SRV (reverse rotation command) are entered at the same time.

Includes PWM, type-B, FSSB interface on single, dual and triple channel configurations. Please try the request again. ER-22 In slave operation mode, a position control command (servo mode, orientation, etc.) is entered. Remedy Reset parameter value.

Remedy Check power supply, replace Fanuc Board, replace fuse. Please try the request again. Inverter: IPM alarm (M axis) Blinking Inverter: abnormal control power supply A Inverter: DC Link Current alarm (N axis) A. Remedy Replace parts, check connections, review cutting conditions.

Remedy Check connections, replace damaged parts. To enter another mode, first cancel the spindle synchronization control command. This A06B-6055-H206 Fanuc AC Spindle Drive was sent to us for repair with a reported "Alarm 12 and or Alarm 03 problems" As we looked into the drive we found it The specified speed detector cannot be found.

ER-09 When the spindle synchronization control command is entered, neither SFR (normal rotation command) nor SRV (reverse rotation command) is entered. AL-05 : The main Capacitor was not recharged within the specified time. The system returned: (22) Invalid argument The remote host or network may be down. A List of Fanuc error codes can be found further down this blog Switch S1 and S2 setting on a Fanuc Alpha Servo Drive.

ER-18 When bit 2 of parameter No. 4001 is set to 0 to specify that a position coder signal is not used, orientation by a position coder is specified. Alarm 02 (AL-02) Excessive Speed Deviation Causes Overload, transistor module is damaged, loose connections, error with speed feedback signal, blown fuse. Alarm 09 (AL-09) Heat sink is overheated Causes Cooling fan is defective, overload, dust and dirty. The red charged led should be lit.

Check the sequence. Enter the slave operation command in normal operation mode only. ER-24 In continuous indexing with orientation by a position coder, incremental operation (INCMD = 1) is first performed, after which the absolute position command (INCMD = 0) is entered. For MRDY, check bit 0 of parameter No. 4001, specifying whether to use the MRDY signal.

Error 39 1-Rot Cs Signal Detect 40 No 1 Rot Cs Signal Detect 41 1-Rot Position Coder Error 42 No 1 Rot. Speed 50 Spindle Control Over Speed 51 Low Voltage DC Link  Alpha PSU faulty 52 ITP Signal Abnormal 1 53 ITP Signal Abnormal 2 56 Inner Cooling Fan Stop 57 Ex Please try the request again. Generated Sat, 15 Oct 2016 13:26:11 GMT by s_wx1094 (squid/3.5.20) ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.7/ Connection

Need Fanuc Spares Alarm Code Fault Remedy - Not Ready Drive is Good 0 Control Ready Drive is Good 1 Internal Fan Stopped Replace/Repair Servo Drive 2 Low control power voltage Your cache administrator is webmaster. Buy the Full Version Servo Spindel Alarm by Baldev Singh1.9K viewsEmbedDownloadRead on Scribd mobile: iPhone, iPad and Android.Copyright: Attribution Non-Commercial (BY-NC)List price: $0.00Download as PDF, TXT or read online from ScribdFlag Remedy Replace fan, review cutting conditions, clean parts.

AL-02 : Cooling Fan Stopped. Alarm 07 (AL-07) Excessive Speed Causes Incorrect parameter setting. ER-10 When the Cs contouring control command is entered, a another mode (such as the servo mode, spindle synchronous control, and orientation) is specified. Series of Fanuc Alpha servo amplifiers from A06B-6079, 6080, 6089, 6090, 6096, 6097.

Alarm 08 (AL-08) High Input Voltage Causes AC power supply too high, incorrect setting of toggle switch for voltage setting. ER-16 When bit 5 of parameter No. 4000 is set to 0 to specify that the differential speed control function is not used, DEFMD (differential speed mode command) is entered.