ge oven f3 error message Washoe Valley Nevada

Address 2321 N Carson St, Carson City, NV 89706
Phone (775) 687-2200
Website Link http://computerbaseusa.com
Hours

ge oven f3 error message Washoe Valley, Nevada

ice maker will not cycle even after 10/15/2016 10/15/2016 smitty1486 I have a Maytag 2000 front loader, model MHWE200XW00. Nächstes Video GE profile oven keypad not working easy DIY $0 fix - Dauer: 2:12 Jim's Good Stuff 1.557 Aufrufe 2:12 GE Profile Oven - Dauer: 8:01 Dan Mirabito 4.288 Aufrufe Results 1 to 8 of 8 Thread: GE oven F3 error message. Login|Contact Us Appliance Need Appliance Repair Help?

Melde dich bei YouTube an, damit dein Feedback gezählt wird. Usually an F3 is a sensor issue. With a multimeter, check the resistance of the sensor at room temperature and it should be about 1080 ohms. Bitte versuche es später erneut.

Reply With Quote January 7th, 2007,01:45 PM #5 DAVIDHELMLY View Profile View Forum Posts Member Join Date Dec 2006 Location Georgia Posts 4 Now that i look at it again it Since your sensor was reading bad and the new one didn't fix the problem, Changing your control board will fix it for you. Open the door and remove the 3-4" long thin metal rod attached to the back wall. If it isn’t, the problem is the temperature sensor.Or it might not be the temperature sensor.Sure, it is then a wiring fault or control board fault.Now we’re back to reboot and

Is the fan limit swtich the likely cause? What does F6 represent?Assuming you didn’t hold down the keys too long, it is the error for a shorted keypad. The mounting screws can sometimes be rusted or seized in place so make sure a good screwdriver is used so the screw heads don't get stripped in the process. Sensors and control boards can be purchased at AppliancePartsPros.com.

disclaimer and Terms of Use. Wird geladen... Add Thread to del.icio.us Bookmark in Technorati Tweet this thread 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 Overnight or Rapid Shipping Now using your ohmmeter , measure resistance between the wires going to the sensor.

Wird geladen... Über YouTube Presse Urheberrecht YouTuber Werbung Entwickler +YouTube Nutzungsbedingungen Datenschutz Richtlinien und Sicherheit Feedback senden Probier mal was Neues aus! Here is the control board for your model in case you need to order it: Electronic clock control kit Jake Appliance Repair School 1987-1988 Star Appliance Tech. 2 yrs. 1988-1990 Wards Donate to let this website help you next time! On models employing that extra safety device, it can sometimes be found inside the control console.

Be sure to turn the range or oven off at the breaker again when you have finished. Once off you should see the two small wires that are from the sensor then you need to disconnect them (some have a plug but if you have to cut the I just cut off that connector plug on the new sensor and use ceramic wire nuts if its hard wired in. Diese Funktion ist zurzeit nicht verfügbar.

Then put the oven or range back together, reconnect power and wait at least one day. You will need to use an Ohm meter to check the resistance of the temperature sensor. Testing the Oven Sensor Testing of the sensor has to be performed while the problem is occurring. Keypads and control boards can be purchased at AppliancePartsPros.com.

By reading any content on this site you agree to AppliancePartsPros.com , Inc. I would suggest bigger screws. Schließen Weitere Informationen View this message in English Du siehst YouTube auf Deutsch. Rick OWNER RICK'S APPLIANCE REPAIR APPLIANCE TECHNICIAN FOR 31 YEARS REFRIGERATION SPECIALIST ONLINE SERV TECH: ApplianceBlog.com CERTIFIED TYPE 1; TYPE 2.....REFRIGERATION SERVICE E.S.

Wird geladen... The control board is bad and needs replacing. Schließen Weitere Informationen View this message in English Du siehst YouTube auf Deutsch. How to access the electronic control's connections will depend on the design of the particular appliance.

Anmelden Teilen Mehr Melden Möchtest du dieses Video melden? If I am reading my ohmeter right it is showing about 6000 ohms at room temp. Melde dich bei YouTube an, damit dein Feedback gezählt wird. I suspect the cold spray the tech put on the limit switch freed up the contacts.

Shop Parts Repair Help SEARCH Return to previous page GE Range/Stove/Oven Displaying Fault Code F2, F3, F3 or F4 JGB920SEC2SS Oven temperature sensor circuit error The manufacturer has assigned this error Appliance-repair-it.com is a free service but it cost to keep it up and running. I told the tech I wanted some time to see if I wanted a new oven and would call back. What's New?

So I would replace the sensor. Once off, you should see the two small wires that are from the sensor and you need to disconnect them (some have a plug but if you have to cut the If the sensor is open (or not within that range) replace sensor, if not check the wiring between sensor and control. Top 6 Reasons Electric Oven Won’t Heat?

Some Kenmore range models have a thermal fuse in the wiring harness to the oven sensor. On some models the keypad and the control board are made together, if so replace control. Best thanks in advance for your help. Thanks #9 (permalink) 12-24-2010, 04:48 AM kayakcrzy Senior Expert APP Volunteer Join Date: Feb 2008 Location: Missouri Posts: 2,429 It does need a good tight fit.

If you don’t find any loose connections, I would recommend changing the sensor even if it checks good cause it could be intermitting. F1 is usually due to a problem with the control board.That’d be fixed by power cycling too.The issue is usually caused by a failed transistor in the control board, which means Replace the oven sensor. Wird geladen...

So, that is something I don't know on your model. Your question was published, help is on its way! Kategorie Wissenschaft & Technik Lizenz Standard-YouTube-Lizenz Mehr anzeigen Weniger anzeigen Wird geladen... Transkript Das interaktive Transkript konnte nicht geladen werden.

This can be caused by either a bad oven sensor or a bad display relay control board. If not you need to figure out which one to change.