ford ranger p1443 error code Pioche Nevada

Address 3331 S Carson St, Carson City, NV 89701
Phone (775) 546-2622
Website Link http://www.computercrew.com
Hours

ford ranger p1443 error code Pioche, Nevada

It cost about 84 bucks I believe. Take the canister off (easy job) and inspect it for damage or leaks. Quote: Originally Posted by aaron_ariens I think Henry just shit himself Quote: Originally Posted by Radness Its kind of like that carnival game "Whack A Mole" but with guns! Quote: Originally Posted by cvar Yes, bullet 6 (below) says the solenoid should be closed (cannot blow thru it) when no electricity is applied.

Can you by chance give me any info that I can use to assist them in locating it? At some point it has to be emptied. Thanks for the information!!! Join Date: Nov 2009 Posts: 5,005 Re: P1443 Error and CEL Help Next thought, create a sig so I know what all is in your truck.

It should "click" immediately. Ask a question to our users or find an automotive repair shop near you to help fix the OBDII code Ask a Question Find a Shop Related Information Help AutoCodes.com Help Truck built in loving memory of Norm Howard Outcast Racing PNW Crew!!! converter.

Thanks again!! Ranger-Forums Office Member Introductions Ranger-Forums General Forum General Ford Ranger Discussion New Ideas Auto Detailing 101 Ranger Products, Company, & Member Reviews Snapshots & Videos Trip & Trail Reports Ranger-Forums Technical Switching O2 Bank 1 Sensor 1 Sensor/LeanP1132 = " " " " " Sensor/Rich Located on Pass. Quote: Originally Posted by Rangerinvegas I have my CEL on and the test they ran said it was the P1443 code.

So I eventually bought a scan tool and I'm only getting one code which is P1443. Can someone help me out with this? The problem went away. i will check the other areas you told me.

Thanks in advance for any advice. Haha richarddhoward View Public Profile Send a private message to richarddhoward Find all posts by richarddhoward #5 09-22-2010, 04:27 PM snackdog Liking the Ford Ranger Forum Join Date: Ewwwww! Top Top Mohawkmtrs Posts: 2049 Joined: Sat Sep 09, 2006 4:26 pm Location: Tyendinaga Mohawk Territory, Ontario Re: 96 Ford Ranger 4.0 4WD, 185k: P1443, P0401, P1131 & P113 Quote Postby

Dana35 swap. 5 speed swap. Posts: 577 i checked my setup. I just don't know where to begin though, I see people talking about buying the complete set with hoses and the canister and sensor all together but I can't find all cvar View Public Profile Send a private message to cvar Find all posts by cvar #26 07-11-2014, 10:09 AM GreatDane A lonely dane Join Date: Nov 2013 Posts:

What engine, tranny, is it 4wd etc. Thanks in advance! -Kimmy C. Schließen Ja, ich möchte sie behalten Rückgängig machen Schließen Dieses Video ist nicht verfügbar. With voltage applied you should be able to blow through the valve.

Installation was easy. I'm not no vampire! Everybody online seems to list CP416 as a "canister purge valve" or "canister purge solenoid" but I think it's the Purge Flow Sensor. Is that where it is on the '96 also?

Spring is out on the Tug too. Abort abort abort!! Join Date: Nov 2009 Posts: 5,005 Re: P1443 Error and CEL Help Quote: Originally Posted by snackdog I have the same problem -- where is the Canister Purge Solenoid/Flow Sensor so Tech.

After doing some research I found the part for $18 at rockauto.com I also ordered new hoses and a gas cap.. That's the first thing to go!!! Leave a comment below or tell us if the information above help you fix the code. I've replaced the vacuum lines from the manifold to the carbon canister, and also replaced the purge flow sensor.

Usually these type of valves are direction-of-flow sensitive, so be mindful of orientation. I'd replace that. General Discussions Bronco II & Explorer Specific Mazda B-Series Specific Rare RBV's Fullsize Trucks Fullsize Ford Trucks The solenoid is supplied 12-Volts when the key is on.

thanks a lot. I did some research on the web and found that the problem could be the Canister Purge Assembly. padrejerry View Public Profile View Gallery Find all posts by padrejerry #8 12-01-2004, 07:03 AM Rockledge Post Fiend Join Date: Jan 2003 Location: Connecticut Posts: 9,615 Pretty sure if so can anyone tell me where the canister purge solenoide is so that i can replace it?

my flow valve and solenoid don't have any arrows on them. Attached Thumbnails Last edited by Lambeau; 05-24-2011 at 01:18 PM. + 0 - #18 01-21-2015 Lonesomejack Member I am: Chester Harbut Join Date: Jan 2015 Location: It doesn't look too bad, but I am not seeing any bolts or screws and don't want to just start pulling sh*t apart... About 50 miles later Check Engine light reappeared...

I've done some reading of other threads here related to the OBD II code P1443 and have found the threads very useful. Your information has been invaluable. Wenn du bei YouTube angemeldet bist, kannst du dieses Video zu einer Playlist hinzufügen.