fax error 388 Laughlin Nevada

Address 1159 Highway 95 Ste B, Bullhead City, AZ 86429
Phone (928) 219-6946
Website Link
Hours

fax error 388 Laughlin, Nevada

Submitted: 6 years ago. Ask the remote machine user to resend the fax. First Time Here? Error Code(s) Definitions/Causes Solutions 344 345 346 347 348 349 ECM 350 ECM 351 ECM 352 ECM 353 ECM 354 355 The remote machine failed to respond to a fax command

Keep getting error code 388 'Image on Fax Send Report is set to Off'. If this holding period exceeds a machine’s specific timeout value, the session is terminated. If the fax fails when sending to other machines, turn it off for 10 seconds, turn back on, and then try sending again. Try sending a fax after each new addition.

If the document is large, ask the remote user to re-send the document as two or more smaller documents. Enable the BFT capability on the remote machine if supported. You should try again at a different time. Meaning that the line was busy or not in service at the time.

Call the telephone provider if line conditions fail to improve. 291 292 The received fax could not be stored. Configure the local fax machine to use a slower reception speed. Wait several minutes between the end of one transmission and the start of the next transmission. 383 ECM Disable ECM, and then try faxing again. If you want remote polling, confirm that you have correctly configured the local machine for poll transmission. 229 The remote machine attempted to initiate a secure poll transmission from the local

I faxed over from a hp photosmart c6180 all in one series printer. HP fax products are designed to work with a two-conductor phone cable. Turn both the sending and the receiving machine off for ten seconds, turn them on, and then try sending again. The user called the correct number, but the machine was configured not to answer.

Confirm that the remote fax machine is ready to receive a document, and then try sending the fax again. 313 A busy signal was detected each time the local machine attempted The paper is not correctly loaded and the document sensor cannot sense it. Add your answer Source Submit Cancel Report Abuse I think this question violates the Community Guidelines Chat or rant, adult content, spam, insulting other members,show more I think this question violates For example, the local machine wanted to initiate polling, but the remote machine did not support this mode of operation.

I can make robot faces ... Reduce or enlarge the page size setting on the local machine to a size supported by the remote machine. 319 The local machine attempted to initiate a binary file transfer (BFT), Reply 0 0 « Message Listing « Previous Topic Next Topic » Related Documents HP Printers - Using HP Diagnostic Tools for HP Printers in WindowsHP Printers - After Windows 10 Credentials confirmed by a Fortune 500 verification firm.

Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print Email to a Friend Report Inappropriate Content ‎09-18-2011 08:33 PM The paper feeder will not work all thetime and These errors can occur if the phone lines in the area to be faxed are old or there is noise (static on the phone line). Interpreting fax receive error codes This table contains fax receive error codes. Reply 0 Reply 0 0 pcwizard Provost Posts: 12,147 Member Since: ‎12-31-2009 Message 2 of 2 (3,442 Views) Report Inappropriate Content Re: hp officejet 4500 wireless fax.

Reconfigure the local fax machine to use different configuration settings, enable or disable the ECM setting. 223 ECM 224 The local machine was unable to receive an entire page even after A splitter could cause noisy lines too. What is support code C000 10/13/2016 10/13/2016 Nathan I have a canon MG5420. Insert a new phone cord if you're using an old cord for your Officejet 7130.

Move to the next step if you still can't send a fax. This might occur naturally depending on when the fax session is terminated. This error does not result in the session being terminated immediately. Confirm that the local user really wants to attempt a poll reception.

Ask the community! I have tested it and am able to receive faxes but get error 388 when I try to send out a fax. The noise problem might go away over time. You can only upload files of type PNG, JPG, or JPEG.

Please upload a file larger than 100x100 pixels We are experiencing some problems, please try again. Search the Community Entire ForumThis CategoryThis BoardUsers turn on suggested results Auto-suggest helps you quickly narrow down your search results by suggesting The remote machine automatically ended the call immediately before, or just as the local machine answered the call. Retry the fax reception when telephone line conditions have improved.

Call the telephone provider if line conditions fail to improve. The user at the remote machine might have pressed the Stop key. Poll transmission from a remote machine is typically configured with each fax session. The only solution listed for this error is to wait and try again later to see if the line condition might have improved or to contact your phone company and let

Had fax for year been fine, now not working. If ECM is enabled, then disable it. Disable ECM, and then try to receive the fax again. 247 248 249 ECM 250 ECM 251 ECM The remote machine is locked. Trending Why will my printer not print from pc but will scan? 9 answers Morning how can i make front and back copies in a photocopy machine? 7 answers How do

Also make sure the remote machine is attempting to initiate a transmission and not a reception. 243 244 The user of the remote machine pressed the Stop key, causing the session Ask IT Technicians for Answers ASAP Not a Printers Question? Ask the remote user to reconfigure the sending fax machine to send using a standard (letter or A4) page width. 281 282 ECM 283 284 285 ECM 286 290 The telephone View Solution.

Expand» Details Details Existing questions More Tell us some more Upload in Progress Upload failed. Replace any four-conductor cables with a two-conductor cable. Thank you! Register · Log In HP Support Forum Home > Printers > LaserJet > Fax error code 388 - how to resolve HP Support Forums Join in the Thedocumentcan be foundhere.

Any suggestion. Most likely this is not going to work based on the error you are receiving. -------------How do I give Kudos? | How do I mark a post as Solved? --------------------------------------------------------I am