f5 error code whirlpool washer Fullerton Nebraska

Address 616 Park St, Stromsburg, NE 68666
Phone (402) 764-2323
Website Link
Hours

f5 error code whirlpool washer Fullerton, Nebraska

Rating is available when the video has been rented. It should be approx. 115 Ω. 4. Verify there is not a siphon problem. 2. Perform test program.

Reconnect the unit and power to verify the pressure switch is operational, as well as the flow meter (blow air through the flow meter and measure resistance). F7-E1 - Common Switch Wire Is Defective - This error occurs when common wire to latch switch and door switch is shorted. Loading... Check the fill hoses and inlet water valves.

F13 - Dispenser Circuit Error - Disconnect power and unplug unit to check mechanical linkage from dispenser motor to top of dispenser. Door not opened during 3 consecutive cycles. 1. This may indicate a bad pump, an extra heavy load, excessive detergent or excessive suds. All other trademarks are owned by their respective companies.MSRP is Manufacturer's Suggested Retail Price and may not necessarily be the price at which the product is sold in the consumer's area.

F1 Board failure Replace control board (also called ERC or clock). Check Pressure Switch harness for continuity. 2. Check the drive motor for powered rotations. 8. Sign in 48 Loading...

Replace control. Check the inlet valve for proper shut off. 7. Unplug the washer and check the wire harness connections between the RPS and the main electronic control board. Check sensor, sensor harness, and the sensor harness connection at sensor and oven control.

HE detergent F0 E4 High water temperature in the rinse cycle Make sure that fill hoses are properly connected. It should measure about 50,000 ohms at 77 degrees. Press and HOLD start to continue the cycle, or press off/pause to clear display. Drive motor, wire harness F51 Motor RPS failure The motor RPS (Rotor Position Sensor) detects the speed of the drive motor.

If no damage to wires and all connectors okay, proceed to step C. Unplug washer or disconnect power. 2. Press 'Stop/Cancel' to clear display. Question about Whirlpool duet Washing Machines 2 Answers Washer door will not unlock.

All rights reserved. The reason for most of these codes back then was a loose wire harness, but this time, this one was actually broken.A temperature sensor is employed in many washers with electronic Check the pressure switch. 8. If all connections are good, then check the individual switches as outlined for the F5 failure. 2 Digit Failure Codes F0 Board failure Replace control board (also called ERC or clock).

Check the electrical connections at the pump and make sure the pump is running. 4. Harold Jackson 110,192 views 3:39 Locating and Repairing a Leak in a Front Load Washer - Duration: 6:16. F2 - Oven Temperature Is Too High - Check for welded contacts on bake and broil relays. Verify pressure switch operation. 8.

Check if the hose is not blocked. Unplug washer or disconnect power. 2. Unable to proceed the request.Please try again © 2016 Sears Brands, LLC Privacy policy California privacy policy Careers Product recalls Terms of use Hide for questions or assistance, call1-888-206-3625 (Se Habla Some models incorporate keypad in to control board as one unit.

Brand WHR Media faulttree Topic assistance Tags This page has no tags. © Copyright 2016 Whirlpool Home Appliances Powered by MindTouch Skip to main content ChatFind a RetailerFAVORITESProductsLaundryWashersDryersWasher/Dryer PairsWasher/Dryer CombinationsFabric Allow at least a minute after power has been restored and if error code reappears, replace control board (clock). Unplug washer or disconnect power. 2. As temperature goes up, the resistance goes down.

Verify CCU operation by running a Diagnostic Test or any cycle. Check the connections between the Steamer 3. Replace the suspension rods/springs in that situation. Working...

Plug in washer or reconnect power. 4. Door lock mechanism is broken. Replace probe if all else checks out ok. By passing a small current through the thermistor circuit, the control board can very accurately determine the temperature of the water within the tub.Thermistors can be easily checked by reading the

Lid lock/switch assembly F01 Main electronic control board failure The main electronic control board is also called the machine control board. Duet Sport Washer Failure Code Condition Check/Repair F01 EEPROM ERROR A communication error between the Central Control Unit (CCU) and the EEPROM onboard the CCU occurred. Refer to the Water Temperature Sensor section. Refer to the Water Temperature Sensor section.

Reach up along the inside of the front panel and locate the bottom of the door latch assembly. 4. Unplug washer or disconnect power. 3. Please check back in a few minutes. If the drain path is clear, unplug the washer and check the drain pump.

This should clear the unit of the excess detergent. 1. CA / CI - Average Current Limit / Instantaneous Current Limit - This error code may signify a problem with the drive motor, thermal protector, or motor controller. Verify CCU operation by running a Diagnostic Test or any cycle. Ask Anonymously Popular Products Whirlpool Gold Duet GHW9400P 3.8 Cu.

If there is water in the unit: Verify drain pump operation. Check the electrical connections at the pump and make sure it is operational with no debris or blockage. The machine will drain for 3 minutes before unlocking the door. 3.