genicom interlock error Winigan Missouri

Address 1821b S Baltimore St, Kirksville, MO 63501
Phone (660) 665-5666
Website Link
Hours

genicom interlock error Winigan, Missouri

GEG-99054GenicomMar 00 microLaser 210 User Guide 9-11Solving Offset Catch Tray ProblemsInterpreting Offset Catch Tray Error MessagesThe printer control panel displays error messages when there is a problem with the printer or Close the rear cover.Correcting Miscellaneous Offset Catch Tray ProblemsSome offset catch tray problems may not cause an error message and may not interfere with the operation of the printer. jano_leroy 2015-02-20 02:25:51 UTC #7 Ho ok my bad, thanks again for your help, gonna try to contact the seller... Genicom Action Load print media into the envelope tray.

Some error codes indicate much more serious problems that may require the help of a service technician.■If the offset catch tray is inoperative after installation, refer to “Installation Problems” on page The system returned: (22) Invalid argument The remote host or network may be down. Replace the top cover of the printer. Ante_Vukorepa 2015-02-20 01:53:17 UTC #4 Oh.

Hide thumbs Also See for 3850 Programmer's manual - 217 pages 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 Buy the Full Version You're Reading a Free Preview Pages 39 to 161 are not shown in this preview. Sign up! Generated Sat, 15 Oct 2016 16:32:31 GMT by s_ac4 (squid/3.5.20)

More Info Sign In Upload Page of 212 Go Download Table of ContentsContents TroubleshootingTroublesh.. If a door is not firmly closed, the interlock switch can bounce between being activated and being not acti- vated—confusingthe system and causing erratic operation.2.Reinstall the printer driver software.The printer driver Press the ON LINE condition. If you are experiencing one of the problems listed below and there is no error message shown on the control panel display, refer to the procedures in the following sections to

Press the ON LINE key to clear the error condition. If this error is displayed during the parking procedure of fanfold paper, first press the ON LINE key to cancel the jam message and then the PARK key again, to complete but I think that isn't the right way to solve this problem..... When a door is closed, the interlock switch is activated and the offset catch tray can operate.

TRAYRemove paperThere is a jam at theRemove the paper jam.  offset catch tray.See “Clearing an Offset   Catch Tray Paper Jam” on   page 9-12.    OFFSET TRAY FULLRemove PaperThe offset catch tray isRemove paper from the  full.tray.    OFFSET TRAY The problem is not the lid sensor or the Z axis sensor I tested and they are working properly. Test the printer by printing a few sheets from the main tray. Tell us by voting 0(0 Votes) ©2016 ManualBirds.com About Us Contact Us Terms of Use Privacy Copyright and DMCA Policy Scholarship ERROR The requested URL could not be retrieved The following

OPT: RETRACT TIME ENTER OPT:RET TIME> 1-99 ↓ Confirm Park Y: Upon receipt of the path select or park command from the host, and prior to park current path, the paper Refer to “Removing the Offset Catch Tray” on page 9-7 for complete instructions.6.Remove the offset catch tray cover from the top rear of the printer and replace it with the original thanks Gianluca_Owen 2015-03-04 22:45:23 UTC #14 I solved just installing the version 1.6 of preform.... Press the ON LINE key to clear the error condition.

But i didn't mean "reset", as i've said - this sounds like a hardware issue. Buy the Full Version You're Reading a Free Preview Pages 192 to 232 are not shown in this preview. If a door is not firmly closed, the interlock switch may not be fully activated—resultingin an inoperative offset catch tray.2.Examine the printer driver settings to make sure the offset catch tray If one of the steps in this procedure corrects the problem but the identical problem returns in less than 50 prints, call for service. 1.

Proceed one step at a time until the problem is solved—youmay not need to complete the entire procedure. Kyle_Montana 2015-02-23 14:18:11 UTC #10 Did you resolve this? Publication No. Error or Warning Message Line 1 LOAD ENVELOPE ENV UNIT FAILURE Correcting Miscellaneous Envelope Feeder Problems Some envelope feeder problems may not cause an error message and may not interfere with

OPT: CONFIRM PARK ENTER OPT:CNFRM PARK>N ↓ OPT:CNFRM PARK:Y ↓ Interlock Sensor Y: Enables error indication of rear pull tractor cover or rear pull tractor assembly not installed. whre I can find the 1.7 version? Although exterior dirt should not affect printer performance, an occasional exterior cleaning may be necessary to maintain the appearance of the offset catch tray.1.Turn the printer off by pressing [ O Mar 00GenicomPublication No.

system 2015-03-18 22:45:46 UTC #15 This topic was automatically closed 14 days after the last reply. Mar 00GenicomPublication No. The platform closes the switch and that tells the firmware the platform has reached the top position. Please try the request again.

What Our Users Say Press & Media Contacts Advertising DMCA Policy Brands × Login Login to ManualsLib Don't have an account? Please try the request again. the printer is making weird noise saying the tank is moving up, but it is already up... If the value saved is "99" then paper retract will occur only if TEAR key is pressed or if data is received from host.

The LCD will display PLEASE TEAR OFF. Close the rear cover of the printer.Testing the Offset Catch TrayAfter installing the offset catch tray, use the following test procedure to verify that it is operating correctly.1.Turn the printer on