frigidaire range error code f13 Smithdale Mississippi

Address 601 Bendat St, Mccomb, MS 39648
Phone (601) 249-2552
Website Link

frigidaire range error code f13 Smithdale, Mississippi

I have a Frigidaire gas range model LFGF3014LWC. ft. Gene. gas range frigidaire model f13 code Report This by Manage My Life August 7th, 2012 i have a gas range frigidaire model # FGF368GBJ and it is showing me the F13

NOTE: Generally speaking F1X implies a control failure, F3X an oven probe problem, and F9X a latch motor problem. *RTD SCALE Temperature (°F) Resistance (ohms) 32 ± 1.9 1000 ± 4.0 Gene. What should I focus on next? Frank // Mar 10, 2015 at 7:45 am Gene, Thank you for the advice.

Gene. I have a used stove of the same kind just different color. Question about 30" Self-Cleaning Freestanding Electric Range - White-on-White 1 Answer I get a error f13 F13" error code means "Bad EEPROM identification/Checksum error". The problem has worsened as now the PF code will come up whenever the oven (bake/broil) is selected.

If that does not correct the issue I would recommend contacting a professional. Replaced temp probe and same thing. Gene // Dec 2, 2014 at 10:14 pm Hello George, Sorry for the delay. The oven was working fine until in the last couple of days the PF code would come on after the oven had been on for a while.

Thanks, please let me know and I'll place an order. Severe overheating may require the entire oven to be replaced should damage be extensive.  2. (F11, 12 & 13) Disconnect power, wait 30 seconds and reapply power. 3. (F11, 12 & what are the connectors called and where can you purchase them? 2. John // Apr 7, 2015 at 2:06 pm Hi Gene, I pulled the EOC and the keypad is held on by double sided glue, it is a two piece.

THanks! BUT oven not heating up. Gene // Nov 30, 2014 at 4:31 pm Hello Martha, I will be more than glad to help you and your lovely mother! Press UPPER OVEN or LOWER OVEN to select oven. 2.

Saves me a trip to the store to buy the wires. sensor??? By Model Number By Part Description By Part Number powered by « Clock and touch panel has no power. | KitchenAid Electric Range » Thread Tools Show Printable Version Any help greatly appriciated, stove is 6 months old.

An F13 error code normally indicates that you have a bad EOC (Electronic Oven Control board). Carefully pull it out and, using an Ohmmeter, check the resistance between the sensor wires. creeps up about 20-50 degrees over the setpoint; but the display still shows the correct temp. The part number for EOC is 316557115 You may want to replace the overlay as well because the old one can be easy damaged.

If you checked the temperature probe at the EOC plug then the EOC itself has failed and would need to be replaced. In order to access it you would need to remove the oven from the cabinet. If you ordered the EOC and the temperature sensor from AppliancePartsPros. Frigidaire professional series FGFLMC55GCC The broiler automatically turns on by itself and I cannot turn it off without unplugging it.

what does this mean ? I checked the sensor and and it checked at 1100. Good luck. Please verify the model number and repost it.

John // Apr 8, 2015 at 7:28 am Here is the actual label on my stove. [IMG][/IMG] Gene // Apr 8, 2015 at 2:04 pm Hello John, I did not question You can unplug the range for 1 minute and then plug it back in. Click here to visit Merchant's home page. SO PLEASE WRITE ME BACK AND HELP ME!!!!

Gene // Mar 7, 2015 at 2:29 pm Hello Glen. All rights reserved. thanks for the info Gene, I will be more careful in my next purchase. When I searched for a part it appears you can't just replace the ribbon connector, but have to replace the whole TST panel ($600!!).

I am still receiving the repeating F10 error code. F13 ...bake or broil--get error msg. Previously, a new EOC had been installed (and the ignitor - elements had cracked). Thanks so much for your time and help!

Oven temperature sensor - What a common sensor or temp sensor looks like. Our oven flashed F10 and went into runaway temps. Yes, the temperature sensor tests OK. What Your Appliance Error Code Really Means.