frigidaire range error code Seney Michigan

Address 220 Walnut St, Manistique, MI 49854
Phone (906) 341-2928
Website Link http://www.manistiquecomputers.com
Hours

frigidaire range error code Seney, Michigan

Gene // Jan 4, 2015 at 1:07 pm Hello Eric, If the problem just melted wire harness connector and the temperature probe tests out OK then the easiest solution is to Keep me posted please. Maximum oven door unlock attempts exceeded. Thanks again.

Any info would be great! Get more answers from the people in your networks Tags Frigidaire , Ranges , Wall Ovens , Appliances Click to remove this tagging. In order to properly diagnose the problem you would need to unplug the range and pull it out of the wall. When an oven fails, usually it will stop working and show on the display an error (fault) code which corresponds to a specific problem.  Actually there are only two major parts

Jay // Sep 2, 2015 at 11:53 am Gene, I have a Frigidaire FEF368gba with F10 code coming up. The part number for the EOC is 316207529 Thank you for your question. by Joey S Earned 73,355 community points in Click'>Appliances December 26th, 2008 Comment Give your feedback by voting on answers 1 votes Didn't find what you are looking for? You may want to start the troubleshooting from testing the temperature probe (sensor).

I was out of town. I have heard a few times what sounded like it shorting out from the control knobs on the right side. To test the resistance value of either potentiometer make sure that the shaft is set to the off position, disconnect the wire harness and use an ohmmeter to measure the resistance Check the temperature sensor resistance as described previously.

Can you suggest a fix for this? You can determine it by visual EOC inspection and/or by the wiring diagram for your oven (if it is available). The stove top and the clock work fine once we clear the PF code. Thanks in advance!

Please verify the model number and repost it. Gene. Thank you for your help. Neil // Apr 4, 2015 at 11:09 am Hi Gene, I have read through all of the postings on this page however I am unable to figure out the issue with

Search by the Model number. Built-in ... Please verify it. Thank you for your question.

Last night I tried to use the oven and it started flashing a F30 error. Gene // Nov 21, 2013 at 3:17 pm Hello Dave. By the wiring diagram for your range, both oven heating elements getting power from the EOC. Your question was published, help is on its way!

Thanks, please let me know and I'll place an order. Thanks again! Eric Ehsan Rehman // Jan 10, 2015 at 6:00 pm Hello Gene, We have a Frigidaire Oven, model # FGFLZ87GCA. The system returned: (22) Invalid argument The remote host or network may be down.

Now it wont let me set the clock to the right time. or Is it something else that's causing this problem? If this error code has been shown while the oven was not cooking then the EOC would need to be replaced. Also, just a side note I have purchased various parts from appliancepartspros.com over the years and have always been very happy, top notch business.

I have a frigidaire oven model FGF379WJC, and when I select any button on the oven control panel it displays, "OFF". Sometimes while the oven is on but most of the time while the oven is cooling off. by Fred M Earned 49,719 community points in Click'>Appliances July 30th, 2012 Comment 0 votes at what cost? Is it worthwhile to replace electronic board, or go ahead and replace oven?? Judy // Mar 31, 2015 at 5:11 pm Hi Gene- Thank you so much for the time you put into helping folks with appliance issues!

You may want to call AppliancePartsPros.com customer service at 1-877-477-7278 to find out the ETA. The oven was working fine until in the last couple of days the PF code would come on after the oven had been on for a while. She noticed the oven was cooking very hot. There is a separate membrane switch in your range which would need to be replaced in such situation.

F13 Control's internal checksum may have become corrupted.  Press clear key. You can not check the EOC instrumentally. Gene. steve // Dec 1, 2014 at 11:20 am hi gene i have frigidaire range that keep giving f30 & f31 errors - i managed to reset by tripping the breaker but

If the error code returns, the EOC would need to be replaced. We bit the bullet and bought the EOC, I installed it….and have had no change in operation :(. The EOC part number 316455400 Thank you for your question. replaced EOC.

Any suggestion is highly appreciated. It is giving F11 error. Gene. Close Thank you!

It's possible that you need to replace the electronic control board or the temperature sensor. Gene.