general scsi error Whitinsville Massachusetts

Address 653 Chandler St, Worcester, MA 01602
Phone (508) 314-1391
Website Link http://the-computerhospital.com
Hours

general scsi error Whitinsville, Massachusetts

Multiple beeps may occur. 4A. Why don't the channels that I have defined above channel 99 show up in RasterPlus? scooter6 (IS/IT--Management) (OP) 30 Jul 01 10:38 The only problems I was getting in syslog file was(in addition to the above message that appears in syslog during startup)NOTICE: Sdsk : Unrecoverable Submit a request Return to top Comments 0 comments Article is closed for comments.

If you'd like to contribute content, let us know. Batteries Defective or weak batteries can cause loss of all setup information. They hope these examples will help you to get a better understanding of the Linux system and that you feel encouraged to try out things on your own. Why is the image sent from Photoshop CS3 improperly rendered in RasterPlus?

The card can't communicate using the current cable. Talk With Other Members Be Notified Of ResponsesTo Your Posts Keyword Search One-Click Access To YourFavorite Forums Automated SignaturesOn Your Posts Best Of All, It's Free! Now you should be able to successfully print. Refer to the software vendor for possible patches.

c HARDWARE ERROR The target detected a non-recoverable hardware failure while performing the command or during self test. e MISCOMPARE The source data did not match the data read from the medium. Defects appended by successful completion of the REASSIGN BLOCKS command. Stolen from The Microchannel Enthusist's Page...

LinuxQuestions.org > Forums > Linux Forums > Linux - General SCSI error : <1 0 0 0> return code = 0x8000002 User Name Remember Me? Dead System (no POST, screen blank, no beep) The most likely cause is a device that is shorting out the power supply. The 2 digits of the "Minor Error Code" is dependent on the type of the error and -mostly- only specified when running the Advanced Diagnostics. Always cold boot and run Advanced Diagnostics (go into System Programs and at the main menu do a Ctrl-A) before replacing components when trying to resolve software problems.

Regards tovohery View Public Profile View LQ Blog View Review Entries View HCL Entries Find More Posts by tovohery 08-05-2008, 03:31 PM #2 irishbitte Senior Member Registered: Oct Make a note of the SCSI DEV ID for the printer and the SCSI Adapter ID directly above it. Join UsClose www.makemkv.comMakeMKV support forum Login Register FAQ Search It is currently Mon Oct 17, 2016 3:22 am View unanswered posts | View active topics Board index All Click Here to receive this Complete Guide absolutely free.

Set the SCSI Adapter ID to the SCSI Adapter ID from the SCSI Explorer step. FEPS (STP2002) The FEPS ASIC is a Fast Ethernet, Parallel Port, and Fast Wide SCSI controller. How do I configure OS10 to print to a networked RasterPlus printer? System board.

The tape drive is HP DAT40. If the first rule is followed and you still receive the error message click on Tools...SCSI Explorer. Multiple POST Error Proceedure If more than one error code is displayed, diagnose the first error code first. Close Reply To This Thread Posting in the Tek-Tips forums is a member-only feature.

Which is slightly strange. (Ed. thread80-112393 Forum Search FAQs Links MVPs SCSI error? Introduction to Linux - A Hands on Guide This guide was created as an overview of the Linux Operating System, geared toward new users as an exploration tour and getting started If it is Linux Related and doesn't seem to fit in any other forum then this is the place.

o o o o o o Continuos short beeps. Note that many of us have gotten away with swapping tape drive SCSI cables in recent years but newer systems such as Itanium seem to be much more fragile. Generated Mon, 17 Oct 2016 05:16:42 GMT by s_wx1131 (squid/3.5.20) Main Menu LQ Calendar LQ Rules LQ Sitemap Site FAQ View New Posts View Latest Posts Zero Reply Threads LQ Wiki Most Wanted Jeremy's Blog Report LQ Bug Syndicate Latest

Certification Defect List (C list) The C list is the position information of defective data blocks detected during data block verification after initialization when the FORMAT UNIT command is issued. How do I configure a Konica R Series Minilab to accept jobs from RasterPlus? Find More Posts by irishbitte View Blog Thread Tools Show Printable Version Email this Page Search this Thread Advanced Search Posting Rules You may not post new threads You may The beep indicates POST has run.

I'm using Ultra160 terminator. Also note that non-HP branded tape drives may also be an issue. 0 Kudos Reply yeazas Occasional Advisor Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print Email If only part of the setup is lost, the battery is probably NOT the cause. Click on Edit...Default Queue Properties...General.

Why does my Noristu QSS driver fail with a Network Service Failure(1722) error? As Mike says check syslog Patel RE: SCSI error? Also don't resolve the issue.I'm really glad if you guys can give me some idea.Thanks. 0 Kudos Reply All Forum Topics Previous Topic Next Topic 6 REPLIES Stephan. Set the Connection to the SCSI DEV ID from the previous step.

Notices Welcome to LinuxQuestions.org, a friendly and active Linux Community. By using this site, you accept the Terms of Use and Rules of Participation. End of content United StatesHewlett Packard Enterprise International CorporateCorporateAccessibilityCareersContact UsCorporate ResponsibilityEventsHewlett Packard LabsInvestor RelationsLeadershipNewsroomSitemapPartnersPartnersFind a PartnerPartner If an adapter consists of multiple FRUs (memory for example) remove the optional FRUs one at a time to see if symptoms change before replacing the adapter. Register now while it's still free!

Verify power is on (IS cord plugged in?). Run diags, if no error code displayed _ o Display or display adapter problem. _ o o Display or display adapter problem. _ o o o Display or display adapter problem. [email protected] welcome if you're in a hurry or something -- but post in tek-tips as well please, and I will post my reply here as well. Add the following to the /etc/system file under Solaris 2.x: set scsi_options=0x178 Wide SCSI To enable Wide SCSI under Solaris 2.3, add the following to the /etc/system file: set scsi_options=0x3f8 SCSI

If the target detects an invalid parameter in the additional parameters supplied as data, then the target may have already altered the medium. These are explained when neccessary. If you need to reset your password, click here.