general misprint error 41.3 Weymouth Massachusetts

Address 20 Hancock St, Boston, MA 02114
Phone (617) 456-1120
Website Link
Hours

general misprint error 41.3 Weymouth, Massachusetts

Figure 23: Pulling out on staple cartridge Rotate the green cover on the end of the staple cartridge upward and remove the jammed staple. Printing can continue, but behave unexpected in response to the changed settings. Action Turn the printer off and then on. Replace cable, AC Power Module to DC Controller, connector J208. (P/N RG1-0912-000.) IIP, IIP+, IIIP Only: 1.

The solenoid is at the front right corner. Anyway Im done adding to the thread hope it all works out. See what the printer says it thinks the paper size in the tray is. Using a dry, lint-free cloth, clean any loose toner that might have fallen into the printer.

Check tabs on side of toner cartridge. Paper is jammed somewhere in the paper path or a sensor flag is stuck. 13.X PAPER JAM IIISi/4Si Only: 13.1 Internal - Check registration area, fuser exit sensor flag and sensor. Turn the printer power off and then turn the printer power on. An improper communications protocol might be in use.

Press the SELECT button to print from a different tray.3 To print from the current tray, load the tray with the size and type indicated.4. You might be able to print pages that are more complex if you add memory to the printer. Error 41.6 - IBT detection error.4. If the error persists, contact HP support.

This spring becomes a little soft, cut 2-3 coils off it and refit, it should solve the problem. IIP, IIP+, IIIP Only: 1. 57 Error Unit 1 - Incompatible memory card in top slot. 2. 57 Error Unit 2 - Incompatible memory card in bottom slot. 57.x ERROR (IIISi/4Si alternates with 64 PRINTER ERROR To continue turn off then on Description A temporary printing error occurred in the scan buffer. Error 41.9 - Noise VSREQ error.6.

Check PS102 and PS103 13.5 Paper delay jam at fuser. The system returned: (22) Invalid argument The remote host or network may be down. The problem is "Unexpected Paper Size"... HP LASER PRINTER 4345MFP, 5025MFP, 5035MFP ERROR 41.X 1.

Plug the printer into a wall outlet and see if this resolves the problem. Unexpected paper size or paper type.2. Replace fuser. 2. Toner cartridge tab broken.

by dmzcompute on Dec 1, 2008 at 4:48pm Add comment Please sign in to comment 0 Okay, this is what I did to get it fixed for now:I looked at the top 50.4 FUSER ERROR Description The problem exists with the customer’s line voltage. Worn feed and separation rollers 4. Check entire paper path, check all sensors and flags. 13.21/13.33 Door open jam. 8000/8100 Only: 13.1 Paper late jam at PS2. 13.2 Paper delay jam at PS1 13.5 Fuser output, paper

If the message persists, replace the fuser. Loading Tray 2 or an optional 500-sheet tray Remove the tray from the printer. Paper multi feed or wrong size paper. 4. Power cycle the printer4.Replace formatter and D.C.

If the above action does not solve the issue, contact HP or authorized service provider. I could not see what was supposed to hold either one out. The media is probably wrapped around the fuser roller. Reload the driver or download a new driver from H.P.HP COLOR LASER PRINTER 8500, 8550 ERROR 41.51.The printer was expecting one type of paper from an paper tray and a different

If the error persists, replace the EIO card (HP Jetdirect card). Replace pick up roller.8. If these errors become a frequent problem, replace the DC controller PCA. Usually occurs with smooth media such as.

Those switches only control what the printer thinks is the size of the paper in the tray and have nothing to do with the feeding of the paper. Figure 59: Ensuring the paper is seated correctly Slide the tray completely into the printer. Second make sure your rear support guide is in the proper place. Rotate the cover up, toward the printer.

Ensure that all trays are configured correctly before printing again. If the error persists, replace the stapler unit. If a message persists after performing all of the recommended actions, contact an HP-authorized service or support provider. by moe on Jul 14, 2008 at 3:53pm Add comment Please sign in to comment 0 I've had the same problem for about a year and pulling the tray out, readjusting

Error 41.7 - Feed delay error.5. Top cover open. 2. If the message appears only with a certain software program or print job, contact the software vendor for assistance. Toner cartridge microswitch (SW501 on High Voltage PCA) malfunction. 3.

The paper size PCA on the right rear of the machine likes to start failing causing the machine to think you have legal instead of letter. Wrong I/O cable. 3. If I pull the NIC card out and perform a Cold Reset, it clears the error and it works fine for awhile. AUTO CONTINUE has two settings, OFF and ON (the default).

On the right side of the stapler/stacker, turn the stapler unit toward the front of the printer until the unit clicks into the open position. I read this great forum and found out it was the cassette (paper try) that wasn't properly set to Letter. Press the (Up Arrow) and (Down Arrow) buttons to step through the instructions.