frigidaire gallery wall oven error codes Shutesbury Massachusetts

Address 180 Pleasant St, Easthampton, MA 01027
Phone (508) 797-3300
Website Link
Hours

frigidaire gallery wall oven error codes Shutesbury, Massachusetts

Gene. This you cannot check if itís working properly so I bought a new board. Oven sensor Electronic clock control jeff. Do you think it is the temp probe or EOC??

Maximum oven door lock time exceeded. Gene. See Details Related Pages Appliances 160K followers Follow Frigidaire 134K followers Follow Ranges 619 followers Follow Sweeps Personal Shopper Gift Registry Legal & Privacy | Help | Feedback Help Remember Me? I am getting this number directly from the oven , not the paperwork.

Thank you, Gene. I would not tell them it happened due to bad weather. The part number for the relay board is 316443925 Thank you for stopping by. The instructions on how to adjust the upper or lower oven temperature usually are in the Owner Guide.

The EOC part number is 316418708 You can order it by clicking on the part number. SteveB // May 13, 2015 at 2:57 pm Hello we have a Frigidaire electric range model PLES389ECB it is showing an f30 code I have replaced both the probe and EOC. If oven continues to overheat when the power is reapplied, replace the EOC. Remove the oven door as instructed in the Owner Guide and inspect both hinges.

Do you know the name of a good shrink in the Northeast? There are two different potentiometers with the ESEC control system. F6 No 60 Hz time base 60 Hz time base is required for time controlled cycling. Both of them should read no continuity.

Gene // Dec 24, 2014 at 5:31 pm Hi Ken, Merry Christmas and Happy New year to you as well! Check the wiring in the oven door latch motor circuit. The mounting screws can sometimes be rusted or seized in place so make sure a good screwdriver is used so the screw heads don't get stripped in the process. If you would order the part from AppliancePartsPros.com by clocking on the part number I posted, you have nothing to loose.

Some Kenmore range models have a thermal fuse in the wiring harness to the oven sensor. Thank you, Gene. The motor does not stop rotating.  Press stop key. If you got both error codes while the oven was in day time mode, the correction is to replace the EOC.

The EOC board was recently replaced (F10 went away after new board was installed, but now it is back). You may want to start the troubleshooting from testing the temperature probe resistance. F90 F91   F92   F93 F94 Maximum oven door unlock time exceeded. If there is nothing wrong and the sensor resistance is correct, replace the EOC. - The EOC Part number: AP2127074 Here are the breakdown diagrams and Replacement parts for FRIGIDAIRE FEB30S5ABA

Gene // Mar 15, 2015 at 7:12 pm Hello Robert, Sorry for the delay. Ceramic Wire Nuts How do I test for continuity? Now it wont let me set the clock to the right time. Sign In Register Keep model on this computer temporarily This option is valuable if you expect to revisit Sears PartsDirect using this computer and browser in the future.

I bought laser thermometer for the oven and it would verify the lower temperature. greg // May 17, 2015 at 3:58 pm I got an f1 error code in the middle of baking in the oven. Gene // Mar 29, 2015 at 6:41 pm Hello MML, Sorry for the delay. It can be easily determined by the model number, usually located on the frame behind the bottom drawer or on the oven door frame.

If itís not the board than logic says the problem lies with the sensor. Or should a person stay away from Electrolux? Also the model number you sent is incomplete. The part number for the triple heating element is 316216703 Good luck." Ed // Apr 24, 2015 at 3:18 pm Hi Gene.

Thank you for your question. Gene. Gene. Thank you.

Gene. Gene. __________________ Appliance Repair Expert in Orange County, California.